The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
The modem firmware version 1.1.4 has been certified by Verizon, and the corresponding NCS version is v1.4.2. Now Nordic has released the NCS SDK version v1.5.0. This version...
To the kind attention of Nordic support team,
if it is not much trouble I would like to know what you consider a good/acceptable ble antenna efficiency in
desktop environment...
Hi,
I am using an nRF52832 with S132 and SDK v15.0.0 and already read in the forum about issues related to the SAADC calibration (inlcuing the erratum [86]). The problem...
Hi Nordic,
I have 2 charac i can write, let's name it A and B.
When i write into A, it trig ble_A_on_ble_evt , BLE_GATTS_EVT_WRITE , no problem.
But w hen i write...
I started developing a project on nRF52. My task is to read the value from the light sensor (phototransistor).
The sensor is connected in this way:
my code:
init...
when i Use 2.4G radio to communicate with other modules,like cc2510, i have many questins:
1. as we known that CC2510 ' modulation format of the radio signal ,MSK is only...
Hi,
Maybe this is obvious, but I couldn't find the answer anywhere online. When I power my dongle from an external 3V3 source, can I still plug it in to my computer and...
Hi, during my tests, I use an NRF52 Dongle with the nRF-Connect app as a USB/BLE interface, but now I need to handle some custom data. I have seen that the dongle uses a COM...
Hi!
I'm working on using the SAADC in 14-bit sampling mode (oversampling set to x2) using nRF SDK 17. The supply voltage for my chip is 3.3V, and I have the reference...
Hi @ all, can anyone here recommend me a suitable chip antenna, preferably one with matching regulatory documents in combination with a nRF52840 MCU.
Thanks and best regards...
I am trying to flash a NRF52832 using the J-link EDU mini in the Arduino IDE but I am having no luck.
I have successfully downloaded... 1. J-Link Software and documentation...
While digging for electrical information I came across :
.63ma using HFINT or 1.58ma using HFXO ?
So I hunted down HFXO to see how to switch between them:
But nothing...
please advice how to add "QDEC_NRFX" to the project configuration of 5340
1. it's not on the default menu config
2. I have tried adding under "ncs\v1.4.99-dev1\zephyr...
Hello
I evaluated FOTA using the http_application_update example. This worked so far until I tried to use my own key for image signing. I created my own PEM-file using the...
