Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hello,
I am currently working with nrf 52840, using segger embedded studio (V5.34) and SDK 17.0.2.
For some reason, when I open any example under ble_peripheral, such...
Hi,
I installed nRF Connect SDK v1.4.2 by the tool chain manager and was following the Getting Start guide and entered here.
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
I have two variants of the nrf9160 SIP one being the nRF9160 SICA B 0 A and the other being the nRF9160 SICA B 1 A.
When I use the AT%HWVERSION AT command on the B0...
Hi,
I want to write my own Multilink/UART example from scratch, because I'm too confused from all these examples.
What I need to get that code done? Or has anyone build...
I am trying to download the softdevice to the nRF52840 development kit using the nRFgo but:
1. On nFRgo I didn’t found the “Program softDevice tab”
2. Although the kit...
Hi
Migrating from NCS1.3.1 to NCS1.4.1, the Blinky sample stops working on my custom nrf5340 board. No compile error, but not running. I also have a nRF5340PDK. Works fine...
I want to use long range ble for advertising with nrf52833. I have a PCA10100 SDK board, and I'm running a program with type of BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_SCANNABLE_UNDIRECTED...
Hi!
So I've got one BLE Central and one BLE Peripheral that I should communicate. Ive based the Central code on nrf Connect SDK's "peripheral_gatt_dm" sample. First I...
Is there an existing implementation on how to do diversity (BLE) with dual antennas using nrf21450?
(could also be by using other antenna diversity switches / brands)
Hi! I'm trying to understand the possibility of doing a FW update to an empty NRF52810 chip via a host MCU running Linux. We have this setup on a custom PCB, whereas the host...
Hello,
I have two quick questions about the nRF24L01+ chip that I wasn't able to find from reading its datasheet.
1. Is the chip pre-programmed by Nordic or does it need...
Hi,
What does the AT%XOPERID command do exactly? Does it just return the operator, or does it change settings too, such as bands, system mode, psm, edrx etc?
Kind regards...
nRF SDK: 16.0, Device: nRF52840, module: BTX480XE, softdevice: ANT_s340_nrf52840_6.1.1.hex
The setup:
BLE and ANT running on same device concurrently. The device is modified...
Hi,
I am new to OTA, wanted to explore OTA. Is there any available example code for OTA in the sdk 17.0 or mesh sdk and how to verify it. How to proceed with this?
Thanks...
