Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hi,
I am trying to get Secure UART Bootloader to work and followed the steps mentioned here .
I generated the Keys and updated the dfu_public_key.c file in the project...
Hello,
I'm planning serial wire flash writing from custom board gpio to nRF52840 serial wire.
nRF52840 SWDIO/SWCLK/NRST are connected to a custom board GPIOs.
Is there...
Hi,
We have been working with an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b, Softdevice and FreeRTOS.
We built 2 configurations for...
I’m using nRF52810 in my design and for BLE communication I want to use Data Length Extension (DLE). Currently I’m using SDK v 15.2.0 , S112 and since DLE cannot take place...
Hi,
I have a very strange issue on my nRF5 development kits and dongles. Whenever I load the softdevice and firmware to the DKs or dongles. After sometime, the USB connection...
when I use central and Peripheral all concerned, Eight Peripheral connected to the central 。when I'll connect my phone to the central Peripheral . Device Error
Here's the...
Hello,
I am using a nrf52 DK in an educational context.
For this reason, I am not using the SDK, but implement basic features on a lower level.
I used the implementation...
I would like to confirm that the temperature measurement is sent from the end-device to the coordinator using the example zigbee temperature sensor.
I'm looking at Testing...
With the introduction of mesh_config_file_clear() in 4.2.0 the behaviour of mesh_config_clear() was changed such that only a subset of all the file ids handled by the Mesh...
How to add new i2c based sensor device to ncs\v1.3.0\zephyr\drivers\sensor.
Can you suggest any tutorial to do so as i want to use sensor subsystem which in turn uses i2c...
I have produced ~ 15 different custom board variations that all use the nRF52810-CAAA. They all have the same reference schematic, and use 4 programming pins (V, G, SWDIO...
Hello,
I have an application that uses the SPI- and the TWI-Manager:
But the application throws the error code 17 when the program tries to initialize the TWI-Manager...
Please see Nordic nRF5x Bluetooth DFU upgrade firmware process.
If device is powered off at the step "Copy new firmware" and powered on again device goes into bricked...
I have a peripheral and central that bond with each other. Now until I had peripheral stop advertising on first connection, it was all fine. Now this peripheral needs to connect...
Hi,
On my nRF52840 DK PCA10056 Arduino connector I have mounted some external ST board.
With ST through Arduino interface I am communicating something with nRF52840. ...
