I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I Flashed the DK using segger embedded studio with example "pca10056_s140_ble_debug" After that I am unable to flash "ble_app_uart" example.
I tried another example like...
Hello,
I am trying to do a long term connection test to the nrfcloud. I have updated the nordic sdk to v1.2.0 and am running the asset tracker on the dk board. I have set...
Hello,
I'm using nRF52840 chip with nRF5 SDK 15.2.0 ,Mesh SDK 3.1.0 and soft device S140 6.1.1
I'm trying to protect the flash if a shutdown occurs during a write. Reading...
From what I understand, the nRF52832 supports the following BLE5 features:
-2 Mbps
-CSA#2
-Advertising extensions
The chip does not support the 'Long Range' feature...
Which of the configurations will work and how?
1) Single Nordic device acting as a Nordic_UART peripheral and multiple smartphones with UART application (central) receiving...
Hello,
nRFSD5 v16.0, softdevice v.7.0.1, nRF52840
We have an application where we receive data from mobile application whenever it writes to a certain UUID. The data is...
Hi...
How to read and write to the external flash
I am using sdk 15.2 version, interfacing the development kit nRF52832 with w25q64 external flash via spi. I have read...
Hi,
I have a Thingy:91 v 1.0.0 which runs fine with the provided asset tracker firmware thingy91_nbiot_dfu_2020-04-29_bc7ade8b.hex. Cloud connect also is fine.
I managed...
Hi Didrik Rokhaug,
sdk:ncs v1.2
Routine path:D:\ncs\v1.2.0\nrf\samples\nrf9160\at_client
The routine is attached:
The test results are shown in the figure below: ...
Hi,
I want to update the firmware of my Nordic controller nrf52810( DFU Target ) using ESP-WROOM32(DFU Controller) using BLE protocol.
Please suggest how to proceed. ...
I am trying to communicate between my mobile Bluetooth and a BLE sysyem (Bluetooth low energy chip and evaluation board). The BLE chip I am using is NINA-B301 and evaulation...
I experimented with nRF52840 for 1 month. It was uploaded to the board well before, but suddenly I can't get the port.
So after finding a lot of Q&A, 1. Press button-4 ...
I've just moved over to the latest SDK version 1.3.1 (i uninstalled the previous version before installing the new one)
I installed it via the toolchain manager as usual...
Running an application that is using a 32 Mhz SPIM3 interface and it is working fine on our custom board.
As part of the interface testing, a logic analyzer was used to...
According to what I know, the nRF52840 lacks hardware to support AoA as defined in BLE 5.1. Still, the web page of the device mentions that it supports BLE 5.1. What is the...
