Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Dear Nordic Experts, although the title says it all, please allow me to briefly explain the situation: I'm working on a ble mesh firmware and an accompanying Android app....
Hi,
I have been trying to run nrf9160: AWS_IoT sample on Thingy91 but have been getting the following output in the serial terminal:
I couldn't figure out what mqtt_connect...
The Situation: I am having a Sensor Node that is based on the nRF52832 (S132) and does two things: advertise some sensor data and store sensor data to the internal flash....
I'm porting an application that communicates BLE with a smartphone via nRF52 from SDK15 to SDK17.
It will be Connected, but I can only receive 2 bytes.
Also, even though...
NCS 1.3.0 mbedTLS configuration to the existing app in SES results in compilation error.
The SES project file contains the define like so -DMBEDTLS_CONFIG_FILE=\\"nrf...
I recently came across the Smart Remote 3 product by Nordic. I currently have a product in development that is a remote that has very similar functionality. Even down to the...
Currently I am facing an issue where the board was not able to power up by itself when a USB is port into it. However, when an external source is connected through the debugger...
Hello,
I have a costum board with nrf52832 chip. when I upload example code "/examples/peripheral/uart/" I can see logs coming and loopback test is working great, but when...
I am inquiring about a custom device that hangs in the ble_stack_init(); and the result is a fatal error.
The custom device has an nRF52832
The SDK is the SDK14
The...
Hi,
I am using NRF52810 which acts as a peripheral to send data to the central . The problem is my device is battery operated,So advertising all the times consumes battery...
Hi,
I have Design a new product based on the NRF52840 I am trying to get the lcd up and running so first thing is the pwm for the backlight. I am using pin 1.08 for the pwm...
Hello everyone, We're using a NRF52840 dongle for a Uni project. We got a couple of dongles it. I stupidly used a image on google to know the pinout because it's hard for...
I am trying to use the BluePy Scanner on a Raspberry Pi 3 B+ with a nRF52840-Dongle programmed as a Bluetooth: HCI-uart .
I am able to get the Bluepy Scanner code to work...
Hello,
I have nrf52DK and I want to deploy templates from S130 protocol to NRF51822XXAC. Any tutorial or guidance would be greatly appreciated.
Thanks in advance.
