The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hello all,
We check the custom board with nrf52840(BL654) , but it's hang PC and devices when connect the PC.
When the hang on my pc , we checked windows system event...
I'm using SDK 15.0.0 on nRF52832_xxaa.
I'm currently using RTC1 as a low frequency timer to keep track of time elapsed while my device is sleeping. This works well and I...
Hi,
I modified the UART example to work on different pins i.e. pin 17 and 15 on custom board. When I use printf() to print logs, it works. If I use the NRF LOG to print...
Hello,
I am trying to build a small voltage stimulating probe for a research project I am doing. I was going to originally use the Rigado BMD-350 which includes the nRF52832...
Hello,
I am trying to connect my nRF52 DK to my phone (apologies not desktop) and perform a DFU OTA via the nRF Connect app. I'm using SD132 6.1.1, and uploaded the secure...
Hi,
I am using NRF52832 with softdevice s112 and SDK 15.3. I have 20 bytes of data which I want to retain in RAM during system off. I use the following code so that the...
It happens on a new board. It is possible that an HW problem occurs (Xtall), but how to debug it? How to know if Xtall correctly runs? The same code runs correctly on another...
hi ... i am using nRF52832 ,i want to save the battery so i am planning to use system off mode . how to wake up the device from system off mode using threshold value or either...
Hi,
I'm using the "pc-ble-driver-js" to implement a central on PC, trying to send a file through a Write w/o Response characteristic to a device. It's OK for a small file...
Hi ,
I am trying to merging 2 application hex files for example : usbd_pca10056.hex and ble_app_hts_pca10056_s140.hex using mergehex tool.
I could merge the hex files...
I am trying to use segger linker instead of gcc and followed the below link to port the changes
https://wiki.segger.com/Porting_from_GCC_to_SEGGER_Linker
I have tried...
Hello,
i was wondering if it is possible to have a node in a mesh, that is communicating to a PC via a COM-Port. I know it is possible to communicate via the J-Link Debugger...
I want to control network formation process for coordinator and end device through application layer. I refereed light switch example to understand network formation process...
Hi,
Please help, I've been struggling with this problem for a week and I want to get to the bottom of it.
I have production devices in the field based on s110 v7.1.0....
Hi,
Please help, I've been struggling with this problem for a week and I want to get to the bottom of it.
I have production devices in the field based on s110 v7.1.0....
