Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
So what steps do we need to take to have these two different Python versions both installed & usable at the same time on the same machine?
The ' Installing the toolchain...
I have three PCA10056 development boards and have loaded the BLE mesh light_switch proxy_server onto all of them (SDK v2.2.0) which incorperates soft device S140 V6.0.0
...
Hi all !
I'm struggling to get a frequency jumping protocol up and running and can't figure out how to handle the following situation (please refer to the attached "pseudo...
Let's have light-switch provisioner, server and client.
My question is, how to send a message from a client or a server to the provisioner? In order to send a message, client...
Hi,
As part of my project, I need to use the SD card drivers of the nRF5 SDK and the I2S driver. The issue I am having is the following:
If I use pin 31 as the SCK signal...
Hi
This is a heads up that in SDK15.2.0 and file nrf_esb.c you have the line
m_rx_fifo.p_payload[m_rx_fifo.entry_point]->rssi = NRF_RADIO->RSSISAMPLE;
it should actually...
Hi
My application uses NFC for various reasons, and I need, at runtime to load up to 4 textural NDEF records onto the Nordic NRF 52832's NFC hardware.
If I wanted a simple...
Hey there faced with the following problem:
I have two hardware setups:
1. Laird DEVK-654 (nrf52480) without external oscillator
2. Laird BL654 mounted to a carrier...
I added the Generic OnOff Model from the thingy52-mesh-provisioning-demo to the Light Switch Proxy Client example from the nRF5_SDK_for_Mesh and get a linker error for the...
Hi All, I am polishing the code that we have, working out minor bugs, etc, we use Nordic UART to exchange data between our device and smartphone or tablet, sometimes data...
What is the proper way to temporarily disable the softdevice? Currently I have the following
sd_ble_gap_adv_stop(); bool disabled_softdevice = false; if (nrf_sdh_is_enabled...
hi ,
We developed a BLE slave device with NRF52840.
Well, we are doing product certification, BQB CE FCC, etc now.
One of the items is the 2m rate test, and we want...
hi ,
We developed a BLE slave device with NRF52840.
Well, we are doing product certification, BQB CE FCC, etc now.
One of the items is the 2m rate test, and we want...
Hi nordic members,
I am using nrF51822 board. I want to inform you that i am getting error undefined symbol: __data_start__ at compile time in segger embedded studio for...
Hi Nordic,
For battery_level measurement on the SDK we are using a timer such that for every 5 seconds or 10 seconds if the timer expires then the saadc will be triggered...
