The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi,
We are seeing issues with Segger Systemview Post Mortem Mode. Original issues were revealed on our custom board with SDK 2.6.1. After enabling the feature firmware crashes...
Hello,
I would like to test TX for ltem. I'm using nrf9160. I would like to use: - Band: 1 - Frequency: 1950 MHz - Tx power: 23 dBm - Bandwidth: 5 MHz - Modulation: QPSK...
Hello,
I've recently was checking out the Zigbee Weather Station application running on the Thingy53 and have spotted a weirdly formatted log message regarding temperature...
Hello everyone, recently I received a thingy:91x with an extra truphone sim card.
I am based in Indonesia and want to test the cellular connection from device but doesn...
I built the demo zephyr/samples/bluetooth/hci_usb for my nrf52820, and it worked well.
But when I tried to read its manufacturer name by using command `hciconfig -a`, it...
Hi there,
I want to capture all the logs made by Zephyr and printk() calls. I want to forward these logs via USB using our custom application protocol for debugging purposes...
Hello folks,
I need some help troubleshooting a BLE antenna issue on our custom nRF52840 PCB . Any insights would be greatly appreciated!
Issue:
BLE sometimes advertises...
ncs v2.9.0
nRF52832 DK (NUS central)
nRF52840 DK (NUS peripheral)
1) When connected, see the empty PDU from peripheral to central about 100ms interval.
2) To use...
I'm trying to add an Aquara temperatur sensor to Zigbee shell running as coordinator on a 58233DK.
Regarding the logs in the serial terminal, it looks like the network was...
Hi,
I am using a nRF9161-dk with the nRF7002-ek shield WiFi tracking.
Using the nRF Connect Quick-Start, I downloaded the nRF Cloud Multi-service application and went...
I'm new to Nordic technologies and ML MCUs!
Does the ARM Cortex-M33 core, nRF5340 audio DK devkit, without any other board od periferic, support edge impulse ML? If so...
NCS 2.7.0 nrf52840
I noticed in i2c_nrfx_twim.c there are some calls to pm_device_runtime_get, while in another thread ( thread ) it was mentioned that Nordic is no longer...
NCS 2.9.0
nRF52840-DK
Using the OpenThread CLI example.
After turning on the TCAT function, when using MeshCoP Commissioning, the joiner will experience a system failure...
Hi, we have a NPM1300 chip connected as I2C slave to a nrf5340, acting as I2C master. Everything works fine, but there is a small detail in the NPM user manual that I would...
