Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hello, beginner here. :)
I just bought an nRF51 DK, but have not received it yet.
I decided to test it because my older BLE module (HM-11) only allowed me to scan beacons...
Hello.
I installed all of relevant software tools and compiled blinky_example with nRF51822 Dev B/D.
Unluckily, build result is like below.
._build\blinky_arm.axf:...
I have built an application using SD120 v2.1.0. The app runs fines from 0x1d000. When I run an own bootloader (RS485, no need of interrupts or SD120, no pstorage functions...
Hello, My question is that in sleep mode my nrf51822 current consumption is 0.98mA, with only GPIOTE enable, however when I disable it, the current falls to 13uA, but the...
Can anybody explain me step by step how to set an Timer interrupt with blinky LED sample code, since i am new in Coding. I am using nRF51_SDK_8.0.0_5fc2c3a/ timer example...
Hello--
On my Mac OSX system, an nRF51 DK loaded with the HID mouse example doesn't list as a mouse device (no mouse icon listed in the OS) when I start advertising. Instead...
I am working with the BBC on the Microbit project. bluetooth nRF51822 has an ARM Cortex -M4F CPU which is MUCH more powerful than the ARM Cortex M0 being used as CPU. Is it...
Since it appears that version 1.20 is broken and useless, does anyone know where to get an earlier version for 64-bit machines? A co-worker has 1.17 for 32-bit but it refuses...
Hi, I just got my nrf51 DK, I compiled the BLE_URIBeacon example from mbed and downloaded the hex file, 361.2KB. I pushed the RESET button and connected the USB cable to my...
Hi
I use an avr attiny441 with the nRF24AP2. Communication is over SPI byte flow. After start up, I get the start-up-message from nRF24AP2. That's fine. Afterwards, when...
Hi all,
I tried to implement a software ACK between two NRF24LE1 devices, but failed.
In my tick_interrupt_ISR, I send a frame from device_A to device_B, and I want to...
I would like to start a pwm signal on PIN 15 while BUTTON_1 or BUTTON_2 is pressed. If BUTTON_1 or BUTTON_2 is released, than there should be no signal(low) on PIN 15.
...
I have built an application using S120 v2.1.0. The app runs fines from 0x1d000. When I run an own bootloader (RS485, no need of interrupts or S120, no pstorage functions,...
hy,
i am using s130 as a central device. I can establish a connection and also read the characteristics. I also enabled notifacation for one characteristic. Everything...