Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi All,
I am an electronics engineer but new to nRF51822 programming. I have used the PCA10000 & PCA10001 using Nordic SDK, using nRF Studio etc. In nRF Studio, you can...
I'm using SD110, and in my application I have an array of 64, 32-bit integers.
Typically, the client will only need to read 1 of the 64 values, or write to one of the 64...
I'm just getting started with the nRF51-DK, and I'm still confused about which SD I need to load, and which roles I need to support aka GAP and GATT.
My end application...
Hi,
It seems to me that pin assignment and package is the same for both nRF chips. Can I solder nRF51422 chip instead of nRF51822 for ANT testing purposes on my PCA10004...
Hello,
I have a custom board (was built using the Nordic schematics provided with the Smart Beacon Kit). I am using J-Link LITE to try and program the board.
The board...
Today nRF Toolbox App on my Android 5.0 phone is only recognizing HRM code running on my nRF5182-mkit, not other examples.
Today nRFToobox and nRFUART2.0 Apps both...
Hi,
I hope use nrfjprog.exe to do following things:
HW: nrf1822
download s110 6.0
download bootloader
download firmware
write some values to certain addresses...
Hi,
I've tried to search the documents and the forum for an answer to my question, but didn't have much luck.
We have a custom board that uses a STM32 micro and nRF51822...
Hello,
I am currently trying to find out how the BLE devices keep their connections in sync. According to the spec, the peripheral can have a slaveLatency of up to 32s...
Is it possible to run Master Control Panel and the PCA10001(or the J-Link lite) at the same time on the same PC, or will that cause problems? I guess I could simply try it...
Hello, Can anyone point me if the nRF51 Dongle can be used for connecting the device with an Android mobile.
Have used this dongle for connecting with PC opening COMM port...
Hi,
When pointer the p_conn_params of ble_conn_params_init_t to NULL for ble_comm_params_init(),
the connection will be disconnected fast automatically, test with the...
Hi,
I am using custom nrf51822 board. I am trying to debug through JTAG(segger j-link). While downloading the program into flash, I am getting error like "Error: Flash...
There can search for profiles using the search method of Bluetooth 2.0 (RFCOMM) connection is not a state in the PC Settings in Control Panel, why Bluetooth 4.0 (GATT) is...
hi guy.
i'm developing such a joystick device Board(HID) using nordic nRF51822, BLE mode.
i have tested many android cell phone & pad and i didn't have connection problem...
