Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
Hi,
My goal is to primarily save the audio being generated by the Headset device in the LE Audio samples. I have established Bidirectional stream between the Headset and...
I had received a lot of support in: Replacing RS485 link with NRF24L01+ .
At the moment I have 95% proyect working OK but in one operation mode of my program, after some...
it will take about 25uA~ 28uA.
when I remove R18 R19, set io to input with pullup, it will take about 10uA,
&button1 {
gpios = <&gpio0 5 ( GPIO_ACTIVE_LOW | GPIO_PULL_UP...
Hi, I'm having trouble running the samples/net/aws_iot sample on nRF9160-based board.
Configuration: - nCS: v2.6.0 - modem version: nrf9160_1.3.6
When running the sample...
Hi Nordic Team I am working on a BLE application using the nRF5 SDK 17.1.0 with Peer Manager configured for Security Mode 1 Level 4 . I am encountering an issue related to...
Hi,
We found a very strange problem when designing a product using nrf5340: The equipment is coated with a layer of UV tri-proof paint on the chip of nRF5340 and the peripheral...
Hello,
I have an application where I want to read the voltage of a battery every 5 minutes for this I'm using the Zephyr ADC library. But now I also want to read the ADC...
Hello Folks,
I've got a thorny problem that I've spent an entire day minimizing before even trying to post about it here.
Before diving in, however, here are my environment...
Hello,
I want to utilize two units of nRF7002-DK I have, to evaluate LE bluetooth link between the nRF5340 SoCs. I need access to define CIG and CIS between the two SoCs...
Hello,
Im using custom board carring nrf52820,and i want enable UART to contact with another mcu,this is the Schematic.
NCS V2.6.0.I take Peripherial_uart to Peripherial_hid_keyboard...
Hi,
I have a Zephyr ZigBee project based on the Nordic Light Bulb example and a custom ZigBee2MQTT integration. However, I can not trigger an identification on ZigBee2MQTT...
I am using the nRF52840, which has BLE support but does not have a touch sensor. Can you recommend a module that includes both a touch sensor and Bluetooth?
I'm now trying to test dongle on nrf52840dongle board：
1. west build -b nrf52840dongle_nrf52840 -- -DCONF_FILE=prj_4llpmconn.conf
2. open nRF Connect for Desktop's Programmer...
hi
board : nrf52840dk
sdk : nrf connect sdk v2.6.1
example: matter light bulb
problem:
I want to add another set of PWM to the sample code. How should I configure...
