Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi,
We are using nRF Connect for Desktop as the production fixture to test the BLE function of our products. To automate some testing procedures in production, we want to...
The advertising PHY is set to 1M; is it fixed? If so, I'd like to understand the reason by reviewing the relevant technical documentation. In the example, it is set to AUTO...
Hello.
I have an nRF9160DK and an nRF7002DK. My goal is to set the nRF9160DK to use the nRF5340 as a module to connect to Bluetooth.
There are two main things I want to...
Hello,
I am considering implementing SPI communication as the transport layer for mcumgr in my application. The setup involves an nRF52820 as an SPI slave and an nRF52840...
Hi everyone,
I am using the S25FL064L memory with the nRF52840 microcontroller and I have a reading problem.
I can read the memory using READ4O mode (opcode 0x6B) but...
Hi Nordic Team,
I'm trying to enable modem tracing on the gnss sample code on my nrf9160dk but have been getting the following error:
Per suggestions on similar threads...
Hi All.
Regarding this exercise, are we sure there is no bug in the https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals/ documentation?
After installing...
before setting NRF_POWER -> SYSTEMOFF = 1, I chose a switch button and an accelerometer as external wake-up sources.
both of the wake-up sources can wake up the chip in...
Hi,
I have an application called `main_repo` built using v2.1.1 (the SDK version doesn't really matter). This contains all source code, dts files, Kconfig files, etc. to...
hello Nordic
trying to migrate from ncs 2.5.0 to 2.7.0
well i did the mistake of installing the toolchain via the vs code .. for some reason it installed it in the wrong...
DFU is now implemented on ipads and iphones, as well as on Android phones, and the app platform is nRF Connect. The problem is that the firmware upgrade can be achieved normally...
I was trying to build off of the example of Lesson 6, exercise 3 from the Intermediate course on DevAcademy.
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate...
Hi there,
I am trying to interface SPH0465 microphone with nRF Dev Kit 52832 with the following configurations of I2S:
I have followed the code from echo example...
Hello!
I am hitting a really frustrating issue running Zephyr on a XIAO BLE Sense module which is based on the nRF52840 MCU. I am simply trying to verify development setup...
