Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Dear Nordic developer community,
I am in the process of developing a communication with the PC via the USB CDC ACM interface of the nRF52840 chip. The information received...
Hello Community! I am working on a small project on nrf52832_mdk beacon Where my main goal is to optimize the current consumption. I removed all the unused peripheral and...
Developing a device based on the nrf5340/nrf7002 pair, with a user interface.
I decided to use the Nordic 'buttons' and 'click-buttons' modules from the CAF framework for...
Hi All,
We are currently using this nRF-5340DK to understand the individual driver functionalities before we start our project with our kit .While doing so we encountered...
I am trying to get a pancake motor working with a nRF5340 using Zephyr in VSC. I have an intermediary board.
I keep getting this error:
I have these settings in the...
HI there, In the Serial LTE Modem documentation for the nRF9160 DK, it is mentioned that the GPIO voltage level should be 3V using SW9 when using an external MCU & UART2....
Hi, I am using the Nordic NRF52832 with SDK 16.
My device is configured to advertise continuously for a specific duration.
However, when tested using the nRF Connect app...
I am attempting to get the BMI270 sample working on an nRF5340DK, using nRF Connect SDK v1.6.0, but all attempts at device_get_binding("BMI270"), device_get_binding(DT_LABEL...
We are trying to interface Texas Instruments TMP144 using the UART in nrf52DK. We attach the sensor board to UART pins in nrf52DK put it seems that the transmitted data is...
Hi Mate,
Like most of the other tickets in this thread, I have a large application and need to DFU it using Bluetooth. I know nrf connect is not compatible with the single...
I now want to have the host and slave in SDK17.1.0 to establish master/slave communication.
What if I change? If I use nRF5_SDK_17.1.0\examples\ble_central\ble_app_uart_c...
Hello,
I am using nrf52840 on usb dongle and i would like to measure voltage on a specific ADC input pin.
According to the datasheet, i use P0.02/AIN0.
My problem is...
Version: windows 11, vscode: 1.92.2 nRF connect for VS Code sdk: 2.7.0
Hello,
I am currently using the vsCode extension nRF connect for VS Code. This works fine, if i...
Hello,
I am currently using an NRF52840 microcontroller (powered at 3.3V) to control two IR LEDs (powered at 5V) via an N-MOSFET. The GPIO pin that controls the N-MOSFET...
Hi,
I prepare my custom board on nrf5340, and i have to use 3xUART, 1xI2C, 1XSPI.
Regarding product specification, i see i cannot configure more than 4 (UART,SPI,I2C)...
