Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Restarting the circuit will run the program, and not restarting will not run the program.
I used SES to develop before, and the program would run automatically after downloading...
Hello everyone,
Currently we're working on improving our DALI driver on the nRF52840 chip and NCS2.6.0, because we've experienced issues with transmitting DALI bits with...
Hi,
as a beginner in nrf world I plan to design a mini devkit with 9161. I plan SW pins connector for it to program/debug via Segger j-link and additional UART-USB interface...
Hello,
I am creating a new project that uses the nRF52810 as my controller, and during the development stage, I am using the PCA10040 nRF52832 development board. (I read...
I have three nrf5340 board. Now i want to use one as bis-headset and two as bis-gateway. I want to get two audio from two bis-gateway at the same time. Can i do it? How ?...
Hello everyone,
I'm experiencing difficulties flashing my Seeeduino XIAO BLE Sense board using the nRF52840 Development Kit (DK) from Nordic Semiconductor. Despite correct...
Hello All,
I have been trying to get the Xiao BLE Sense with the nrf52840 chip in conjunction with the expansion board to access the SD card using the FatFS example from...
I don't want to use nrfjprog as the runner. I want to use jlink runner when flashing. However it doesn't work, neither do nrfutil.
nRF Connect for VSCode doesn't work when...
Hello,
OS: Ubuntu 22.04
SDK version: NCS 2.6.1
Modem firmware version: nrf91x1_v2.0.1
We are evaluating NRF9151 in a new design. We have some prototypes built...
For a project we need to evaluate DECT NR+. We have used the `hello_dect` example ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/dect/dect_phy/hello_dect...
Hello, I'm developing an app that will allow a programmer to flash application firmware and modem firmware. I am able to flash application firmware via JLink Commander. The...
Hi, I had a project which was configured with upto 5 simultaneous connections. Recently moved from NCS 2.4.1 to 2.6.1 and now the advertising stops after one connection. I...
Hi,
I want to DFU the nRF52 from nRF91 over UART. And I find this sample: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/cellular/lwm2m_client/fota_external_mcu...
We are working with Zephyr to program the development kit for now and later the real board,
We need access to both UART0 and UART1 but we can't seem to get UART1 to work...
Attempts to build the Matter light bulb same fail for me under these conditions:
A new nRF Connect SDK install on Ubuntu
Toolchain v2.7.0
SDK v2.6.1
VS Code...
