Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hello, Lesson 8, exercise 3, regarding bootloaders and BLE DFU, of the intermediate DevAcademy course had a compilation issue with the nrf5340 DK, and using TF-M. It was caused...
hello,
I tried to apply modifications to use and test the qspi flash mx25r6435f on the nrf9160dk development board. NCS version 2.2.0. I can not see her.
prj
overlay...
Hi,
we are developing a solution where the number of peripheral BLE devices is increasing and we need to manage up to 30 realiable connections. We have been working with...
Hi everyone,
I'm trying to send updated gyro and acceleration values from MPU6050 continuously by BLE function from nrf52832. I'm currently using the nrf52 development kit...
I would like to inquire whether there is a sample or guide to search for and connect to iPhone background advertising when operating with nRF52840/5340 Central.
https...
Hi
Followup on this ticket: Enabling SPI and TWI drivers on Zephyr
First the fundamentals, I am using:
nRF52840-DK
nRF Connect for VS Code: v2024.7.13
nRF...
Hi
First the fundamentals, I am using:
nRF52840-DK
nRF Connect for VS Code: v2024.7.13
I am trying to create a demonstration project, where I need both SPI and...
I am having trouble understanding how to measure the power consumption of the nRF9161DK as recommended by the documentation: https://docs.nordicsemi.com/bundle/ug_nrf9161_dk...
I'm working on a complex legacy codebase for the nRF52840, which uses nRF5 SDK 15.0.0 and the S140 SoftDevice v6.0.0. The device previously only used a custom RF protocol...
Hi,
I'm using SDK 2.1.0 for this project.
I found that when I shut down using the following:
pm_state_force ( 0u , &( struct pm_state_info){PM_STATE_SOFT_OFF, 0 ,...
I was trying to set up partitions on a nRF5340 DK so I can use MCUBoot, settings, and littlefs but am getting this error when flashing the dk:
The output Zephyr.dts has...
Dear Support,
I encounted an issue when tried to connect with complicated wifi network recently.
The error info is as follwing.
"WPA: 4-Way Handshake failed - pre-shared...
Hi,
we use our code for beacons for very long time now. Unfortunately producer changed chip.
We were using NRF51802QF with SoftDeviceS130.
Now the chip is NRF52810QCAA...
I am receiving the following errors: [00:00:00.117,187] <wrn> bt_hci_core: opcode 0x2027 status 0x12 [00:00:00.118,133] <err> bt_id: Failed to add IRK to controller Which...
