I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Greetings,
Using SDK v3.1.1 I've configured 3 PWM outputs using the pwm0-2 modules via a DTS overlay. After reset or power cycle (and prior to making any PWM driver calls...
After cancelling a flash operation to my nrf7002DK (PCA10143 1.0.2), I'm unable to flash my discovery kit again. I have tried both the regular west flash for our application...
Hi,
I use flash read operations at the BLE interrupts, because I need some of the stored informations. However, while I am doing another flash operations and BLE interrupt...
Greetings,
What's the maximum clock rate supported by the SPI1 interface on an nRF52840? My DTS overlay indicates it should use 32MHZ for one device and 8MHz for the other...
I am tried to access the server using http_client .I am tested that my implementation to access the local server works properly but the thing is i am tried to access the ...
I am looking for the datasheet for the nRF31512. I am looking to see what the pinout for this chip is. It is not for any new project as I know it is old and discontinued....
Hi,
1. Does the P1.02 (NFC port) on the nRF54L15 support PWM? 2. If it does, please provide the overlay configuration method and sample code.
Best regards,
Peter.Mi...
Hello,
I am building an example app that uses MbedTLS and non-offloaded sockets, because offloaded ones do not fit my needs - updating security credentials needs disabling...
I get the following error when trying to program the device:
The log shows this:
2025-12-10T09:08:50.194Z INFO Initialising the bundled nrfutil device 2025-12-10T09...
Hello,
we have an nPM1300 EK plus the profiling adapter board and are trying to profile some of our batteries.
We have already successfully completed profiling for...
Hello, I am currently struggling with setup and configuration of firmware for nRF5340. The idea is to use two stage bootloader setup, XIP split to external flash and build...
when trying to implement ISR for writeprotect and powergood pin it throws error code 134 which corresponds to not supported.
call stack for reference.
What am I...
I had a fully working BLE setup on my nRF52 (Zephyr), which worked fine on older Android versions. After updating a phone to Android 16 (tested on Google Pixel 7 and Samsung...
Hi, Nordic support team!
I'm having trouble downloading the NCS in China.
The command nrfutil sdk-manager install v3.2.0 --region cn fails with a SHA512 checksum error...
I have designed a custom board using the nrf54l10 chip (similar to nrf54l15). I want to use SPI to communicate with a sensor. So I assigned the pins P2.6 for SCK, P2.4 for...
