Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Hi,
I have few doubts regarding the internal flash of nRF52810. I am not using SoftDevice. I am using SDK 17.1.0
I would like to write around 20 bytes to internal flash...
board : nrf5340 sdk : nrf-connect v2.1.2
Hi. I am studying OpenAmp and RPMSG using NRF5340DK board.
I looked at the examples below for studing OpenAmp and RPMSG.
C...
nRF Connect SDK 2.2.0 on Windows 10 pro, I have a nrf52840-DK and a nrf9160-DK. I would like to test a simple OpenThread CLI application
I have the following prj.conf
...
Hi, team.
I am trying to find a way to write some persistent data in factory.
The data is a couple of certificates and should be written differently for each devices....
I am a beginner, and there is no problem with scanning and receiving data in RTT Viewer. I am currently stuck on how to use CDC ACM US. i have notice there are example on...
I am interfacing with a part that uses the same pin, P0.6, for two purposes:
1) The pin is used for UART communication. MCU RX input.
2) The pin is used as a GPIO. MCU...
Hi Everyone,
I have a custom board with a nRF9160. I have updated the firmware to 1.3.3. I am using SDK 1.9.1. I found that the board works well with the GNSS sample from...
Hi, I have an application where I need a latency below 100µs between transmission and reception over the air of a 32 bits payload.
We are currently evaluating the ESB protocol...
May I know if developing using the example of proprietary_rf that does not use BLE in SDK is also subject to a user fee? (If there is a usage fee, I would like to know the...
Hello,
I have an issue with BLE-Mesh, wherein If I provision a device and then flash the board with a new image (I do not erase and flash), the device name & provisioning...
Hi all,
we are using UART uart_rx_enable() to define a timeout of 500. Most of the time, event UART_RX_RDY is raised as it should be after a timeout. If, for example, we...
Hi!
Which is the right way to install nrfconnect SDK for VS Code for linux? Is it automatically or manually as described in the documentation?
Regards.
Hello all, I hope you are doing well.
I Have a project on NRF52840 in which I have multiple sensors connected to the NRF52 and the sensor data are storing in the SD card...
I have received a development kit from Farnell. It has version 3.0.0. When I connect an external target, I can't get a connection. It only recognises the onboard chip. An...
Hi there,
I would like to use SMP for DFU my Firmware and communicate with other SoC by one UART port. And then, in SMP protocol specification,I saw there is an ID (64)...
