I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Could someone please tell me if external series resistors are necessary for D+ and D- for USB 2.0? I've seen some comments here that they aren't necessary and may cause problems...
Hello,
I was trying to run TFLM custom code on Thingy:53 device and while building I have faced these warnings.
1. Could you please help me to understand Why I am...
These are the details of my system:
Ubuntu 20.04.5 LTS
nRF Connect for Desktop v3.12.0
Toolchain Manager v1.2.1
Visual Studio Code 1.73.1
NCS 2.1.2
If I start...
I am working with ncs version 2.1.0 in visual studio code, for reference.
I have been trying to get any of the SPI channels set up on the 5340dk with no luck. I've come...
Hello everyone,
We're trying to create an application that has 2 modes, one is running our regular application and upon a special command, it switches to a "DFU" (via device...
I'm testing the thingy91 with asset tracker v2.
I managed to build, flash and get the thingy 91 to send data to the nrf cloud platform perfectly, but as i've seen in the...
Hello,
I am using nRF52840 DK, and SDK version 17.1.0
I dynamically and explicitly request and restart HFCLK clock source after I released HFCLK clock source while...
I am encountering an unusual behavior when I stop/start app_timers from the GPIOTE IRQ. I am implementing a debounce procedure from a GPIO interrupt .I find the timer callback...
I'm using nRF Connect SDK v2.1.2 with Visual Studio Code and a nrf52840DK.
I have implemented this app (OpenThread CoProcessor NCP from Zephyr) and it is working correctly...
Hello again!
I have configured and initialised the Thread API from the Thread/Zigbee client publisher example, and receive no errors or warnings when attempting to send...
Hi,
Is there a possibility to change the COM port number of the nRF52840 USB dongle manually?
I already looked in the device manager under the port tab, but couldn't...
Hi all, I have a prototype device app I'm going to "deploy" in a remote location with an nrf52840 dongle. Initially ble via special shell commands added to nrf/samples/bluetooth...
Hi all,
I'm new to embedded programing with Nordic I'm using the evaluation of Fanstel EV-BC 805M. I was trying to program the basic program for blinky led, however by the...
Hi,
General information:
nRF52840 SoC
Our own PCB’s with inverted F-antenna
nRF Connect SDK v1.8.0
We are in the middle of approval testing our product. We have...
