the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello Devzone,
Working on my Ubuntu 20.04 LTS host, I recently lost ability to flash my nRF9160dk board. The embedded J-Link is detected by its serial number, but an attempt...
Hi, we are working on an application with 300 nodes. each node do 10sec advertsiment and afterwards 10sec scanning pls check the picture below
1) Beacon2 for example advertisies...
Hi,
I have added an external reset switch on my custom board. Maybe a stupid question, but do I need a pull-up resistor? Because in de schematics of the nrf52840 dk I didn...
Hi,
i want to send and receive data via uart1 (connect to a raspberry and send/receive text).
Is there a simple example that shows how to accomplish this?
Im using SDK...
I'm trying to implement a really simple script to sample voltage values from 5 different analog pins on my NRF52832 DK (using Segger at the moment). I found the SAADC example...
While nrfconnect-3.11.0-x86_64.appimage works well, the update to 3.11.1 ends up without Apps.
Ubuntu 18.04
NCS 1.9.1
I found a past case and removed the config and...
Hi,
I am working with NRF52840, I am using segger embedded studio as V5.42a from that I build the example code as ble_app_proximity. I am getting some error as "Output/Debug...
Hello, I am a private developer of wireless gaming mice in Japan. I am thinking of using Nordic's nRF52840 as the MCU, but can this chip be written to only by USB without...
Hi
I added some code to get the PA/LNA driver enabled in the DFU bootloader on my board accordig to this post:
https://devzone.nordicsemi.com/f/nordic-q-a/50687/pa-lna...
Hello! I am quite new to hardware design with these chips, I have been working with NRF24LUP1 for a while, and have custom bin file for it, not a hex file. and I am unable...
Hi,
I am trying to send the data from SAADC on BLE. I follow the example: https://github.com/NordicPlayground/nRF52-ADC-examples/tree/master/ble_app_uart__saadc_timer_driven__scan_mode...
I use PCA10059 demo board,receive BT data by" nrf connect for desktop",yesterday it is ok,but today when I plug it into my PC,it can't be recognized.and no any indicator,...
My peripheral_demo is already able to work. Now I'm trying to add dfu to it.
I followed the instructions here. (+) Add DFU support to your application - Software - nRF Connect...
I have been able to set up external flash for MCUBoot for FOTA.
But after rebooting, the image is the same than before the image upgrade.
I used a sniffer so i could...
