Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
How do I remove nRF Connect SDK from Windows before re-installing?
And are there something that needs to be done, if you have used cmake and Visual Studio Code for other...
Hi,
I want to use in my project the saadc (I'm using segger embedded studio). So, I found that I have to add the driver file to the driver folder, and I have added the file...
im using nrf52840
with sdk 17
and segger ide
i recently discovered that the max count buffer is 16 bits meaning it has a limit of 65k bytes. im trying to receive 100k...
Hi @Torbjorn!
Hope you are doing good!
I tried using nrf52840/nrf52833 ble_app_blinky_c and ble_app_blinky for connectable coded PHY . But it only works for 1M_Phy . Although...
Hi there,
Our current understanding is that when building an application using NCS, the images of of MCUBoot and the application gets merged into merged.hex.
We however...
I'm a relative novice to linker files, just enough to be dangerous, but I have a need to understand what the Segger linker is doing. I have some success using `flash_placement...
Hi
We are trying to connect to connect to a MINEW MS88SF23 SoC from our nRF52833 DK.
For all tests, nRF power source switch is set to VDD, nRF ONLY switch is set to DEFAULT...
I was trying to reflash UICR for the first time on an nrf52840_dongle using nrfjprog. Here is what I tried:
$ nrfjprog --eraseuicr --program /tmp/new-uicr.hex ERROR: Two...
Hi,
I am trying to measure power consumption on a nrf52840-DK dev board running custom firmware.
I am using PPK-2 and nRF Connect Power Profiler app v3.1.2 for the power...
When RTT viewer is not connected, the buffer will eventually overflow and it causes device hanging and being reset by wdt eventually. When I connect to the RTT viewer before...
Dear Nordic engineers
I made some modifications to the keyboard examples in the SDK based on the NRF5 17.0.2 version. I changed to use a static password for pairing and...
Send a semaphore every 20ms through the timer. After receiving the semaphore in the thread, push the data to the message queue
Then, the message queue is obtained through...
Hi
I'm working on adding software flow control in coprocessor code，
1.CONFIG_UART_ASYNC_API and UARTE_INTERRUPT_DRIVEN ，What's the difference between the two macro definitions...
Hi everyone,
I have the following issue. I have migrated a code for a Bluetooth Mesh network gateway which I developed a few years ago with version 2.1.0 I guess to the...
Hi Nordic,
I am trying to implement a custom uart driver in my inter processor communication application. In the driver implementation I want to use uart with dma and I...
