Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
I'm using the flashlog on my nRF52840 to log events. I have an external RTC which I read when logging each event in order to timestamp the event. My RTC code writes...
I am trying to set up a project that uses MCUBoot and puts the secondary slot into QSPI External Flash. I'm using NCS 1.7.1 with VS Code. I've followed numerous posts on these...
I am currently evaluating the differences between nRF52811 and nRF52810. I am still using the nRF5 SDK.
One difference is in the nRFInitialize function in the startup code...
Hello,
In my application (using sdk 16.0.0) I have a bootloader that allows to upload a new firmware through either BLE or UART. The Bootloader is initialized as usual:...
Hi All!
I have a problem running simple PWM output on NRF5340 board. I have a following code:
Now what i'm trying to achieve is to get 50% of duty cycle with frequency...
Hi there,
This should be straight forward but has me stumped. I'm trying to add BLE to my CAF based application and can't do and recreated the same problem with the samples...
Hello, I have a two part question with regard to SPIS setup time when exiting low power mode on an nRF52840.
We are using the SPIS peripheral on an nRF52840. General guidance...
Hello,
I am currently integrating the Wiznet5500 drivers into a VSCode project, but I am stuck on where to include these custom modules.
In the previous version in SES...
Hi，
I have a problem about CAF leds modules. I submit a led event to turn on led for 3600ms and turn off led for 500ms, but it work inversely in fact.
I find that leds...
SD140
Part nrf52833
Application: Central App that connects to 1 to 16 different peripherals. One at a time.
Problem: 1/10th of the time, I get a disconnect reason BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED...
I keep getting a hard fault when calling spm_request_random_number()
I'm following the secure_services sample provided in the SDK, and the secure_services header file...
Hi, I am using the nrf52 Thread v4.1.0 SDK for development
I am using ADA4333
there pin 6 is used for Gate control but
in CLI pin 6 is used as uart tx
and it is hard...
I found the following problem with Programmer v2.0.1, using either a Nordic DK or a Segger J-Trace as the programming device (on Mac OS 11.6, and with nRF Connect 3.9.1):...
Dear All, I am trying to add the task watchdog to my application, but I am dealing with some interesting issues. The NRF SDK that I am using is the v1.6.1 I have dealt with...
Hey,
I saw the example in the SDK for hid keyboard over ble but it is only as a peripheral device.
In my project I have the nordic board as a central device connecting...
