I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
I have a simple prototype platform that previously uses nRF51822 which is discontinued. Now I plan to replace the BLE module with nRF52833.
Previously developed firmware...
Hi everyone ,
I want to perform DFU of SD+Bl+APP via UART.
I use nrfutil version 6.1.3.
The Softdevice is s140_nrf52_7.2.0_softdevice.hex and the application is based...
Hello everyone, i'm trying to deal with the ACS714T sensor but i can't find any samples or guide through internet the communication need to be done through ADC and SAADC HAL...
I am using the nrfx_uart and need to disable the receiption. I call nrfx_uart_rx_disable. When done once, the receiption is not working anymore, even when I call nrfx_uart_rx_enable...
I am the digital pcb and fw designer on a project using a dipole antenna defiend by the RF designer ( I have read the posts discouraging that and have taken that into account...
I am studying the ble_beacon example among the examples provided by nordic.
I want to code the beacon's uuid to indicate the mac address.
I studied to find the mac address...
Hi team,
Note that nRF Sniffer already support nRF52840 dongle, but can that sniffer the BLE5 Advertising extension pack?
How to set the sniffer software?
Thanks!...
Hi,
I'm experimenting with the AoA locator receives IQ data on nRF52833 in ncs1.7.1. It worked well when the locator only received IQ data from one beacon. But when multiple...
Hiya. We're building a custom appliance on top of a Nordic chip that talks to an Android/iOS app developed with Flutter and a custom cross-platform Bluetooth plugin.
We...
Hi guys,
I tried to connect to nRF52832 using the app and it was successful. But when I directly use the BLE in the Android system(android 11) settings to connect to the...
Hi. I am new with nRF52 microcontrollers. I was able to create a project (myproject) in the examples folder and compile it with SEGGER embedded studio. I copied the whole...
Hello
I just downloaded nrf sdk 12.3 and am facing a problem straight away where I couldn't find valid answers that would fix my problems when searching this forum and on...
Hi,
The Bluetooth Core specification states that:
Per Bluetooth Core Specification Version 5.2 | Vol 6, Part F, Section 1.
The nRF5 SDK, v17.1.0, DTM Example states...
Hi,
I have a problem on two things
1. I want to advertise my custom 128bit UUID with ble appearance and manufacturer data but when i did my advertising device name become...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I am trying use dfu update my application program.After i program software device/bootloader/app(dfu example...
