Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hello,
We are currently using the 0.27 and the 0.26 PINs of the nRF52840 for I2C communication as suggested in the sample code. But we need to use the P1.12 and P1.14...
Hi,
I am using nRF52840 as a peripheral + want to add UART to communicate with like Arduino and GSM. Is there any project that I can use/follow. Thanks.
I see LESC_DEBUG_MODE defined in some of the examples in the SDK (17.0.2) but I can't see where this definition is referred to in any of the libraries, so I don't think it...
I am facing strange issue when I execute firmware with NRF_LOG_ENABLED set to 0.
During BLE communication, Firmware is crashing.
If I enable NRF_LOG_ENABLED, all is working...
My requirement program flow is clearly written down .Please help me out.
void USART_EVENT_Handler()
{
// disable timer 1
//disable timer 2
// clear timer 1 count...
HI,
I have already got output from each of the SHT20 and MLX90614 sensors. Now I want to combine both the code. Regards, I need an help to Setup prj.conf file
Thanks &...
I'm referring to the HID keyboard example (BLE peripherals)
The example itself is more or less working and since my goal is to send a whole character string via BLE and...
Hello, Nordic!
When a scan is started with certain scan parameters, a timeout event (NRF_BLE_SCAN_EVT_SCAN_TIMEOUT) will occur in a time less than the specified timeout...
How can I do a point multiplication in NRF52840 using the ECC hardware accelerator for the secp256k1 curve? Also are there examples or any documentation on how to implement...
Hi,
I'm openning a new case (following the proposal of Einar Thorsrud ).
I want to do a BLE NUS project with custom service 128bits and with custom characteristics also...
Greetings!
Using the NRF52840 PDK, I succesfully erase, write and read without any modifications!
I have custom boards which involved a NRF52840 and a MX25R6435F (so same...
Dear Nordic Support,
My project is split into two parts: A firmware application that is based on the Generic Level Server model example (from the Mesh SDK) and an Android...
Good morning,
I'm working on nRF5 SDK v17.0.2 and I am using Segger Embedded Studios (SES) for the development.
I'm having a problem when I want to share my project...
I'm aware that the nRF CLI tools are not yet ported to AArch64 so they don't work natively on Apple Silicon. Normally rosetta 2 is fine, but nrfjprog is not compatible with...
