I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I want to capture 802.15.4 nRF packets with a python script using the pyshark library and an nRF52840 DK sniffer and an nRF52840 Dongle. the problem is that when...
Hi,
I've successfully integrated an out of tree driver using the out_of_tree_driver example in the application_development sample folder for Zephyr; it has built and ran...
Hello,
given that the Micro:bit V2 (Nrf52833 based) has been promoted in Webinars, I am surprised on the lack of enthousiasm in getting it to work properly under NCS/Zephyr...
Hi
I checked how AT%XOPNAME could be used to receive notifications about operator name updates. However I'm wondering about the notification syntax.
According to the specification...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_examples_sdk_coexist_ble_app_uart_coexist_README.html&cp=8_2_3_3_1
In this...
Hi,
I developed some multi peripheral units. and also i developed some central units which are allowed to connect to the multi peripheral devices.
F.E: i got 2 multi peripheral...
dear all
I use nrf52840 to compile a library with floating-point operation. I configured it in my *. Conf
CONFIG_ FPU = y, but we can't find sqrtf, sinf, logf and so on...
For a customer I am developing a Zigbee coordinator / Gateway with the nRF52840. As software basis I use the “Zigbee cli example” from SDK V4.1.0.
So far, everything works...
I installed nRF Connect SDK v1.6.0 and SES Nordic Edition through the nRF Connect toolchain manager (Windows 10). I'm finding that I can't use the "open nRF Connect SDK Project...
Hello,
I'm trying to make the RF frequency of TX channel configurable.
I have noticed that anything higher than 0x50 is not acceptable for sd_ant_channel_radio_freq_set...
Hi,
I wanted to use the console on nRF52840DK in high-speed UART mode (921600bps) but it fails and I just saw the DK User Manual says:
Baud rate 921 600 is not supported...
I'm using the ble_nus_c NUS client code for a custom 1:1 data link between two embedded nodes, just pinging a few bytes of data back and forth every 3 seconds. Bonded connection...
Hi,
We are using nRF52840 SOC with our custom board . Due to some reason, the SWD data line( SWDIO pin ) shorted .
So now we are looking into how we can program nRF52840...
From SDK we can see that there is a lot of events about security. I've read some of them by comments and still a little confused about the difference of them.
Could anyone...
