Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
I have BOARD_ROOT set in both zephyr/module.yml and in CMakeLists, and in my boards folder I have a custom board "boards/nordic/myboard". I have all the necessary files for...
Hi Nordic team,
I’m building an LE Audio gateway on the nRF5340 DK using the TMAP_Central sample (NCS v3.0.2, with minor local changes). The setup captures audio, encodes...
I'm working with nRF52840 microcontroller, nRF SDK 17.1.0 and Softdevice S140 version 7.2.0
The peripheral devices sends 29 bytes of data with a BLE notification from a...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
I'm currently using firmware advertising/scanning with 1M PHY, but I'd like to use Coded PHY instead. I tried changing the advertising parameters as shown below, based on...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi,
I have LIS2DW12 (Gravity board) connected to my NRF54L15-DK with the following overlay:
& pinctrl {
/* Pin control for I2C21 */
i2c21_default: i2c21_default...
Hello,
I have set up the light and light_switch BT Mesh examples on my nRF52840DKs. I have used the nRF Mesh app to provision them successfully and I can see that they work...
Hi,
I am using NRF Connect environment and would like to enable by program to use MCU Boot functionality with dual-imaging support and FOTA updates.
My Kconfig.sysbuild...
Dear Nordic Team,
I am trying to configure logging through J-LINK RTT for my firmware.
My prj.conf contains the following:
CONFIG_PRINTK = y
CONFIG_CONSOLE ...
My current product uses the NRF523840 with CODED_PHY periodic adverts. I want to improve the range.
I'm considering a +14dBm (SAR limited) product variant with the NRF54L10...
The nPM2100 datasheet (v1.0) states in multiple areas that the VOUT pin is discharged when the device enters Hibernate mode (and certain other modes).
Is this discharge...
Hi
It seems that the default minium DTLS handshake timeout is about 1 second. That means, there is a retransmission if a response isn't received within this timeout. In...
Hi there,
I am trying to program my custom board hosting a raytac mdbt53 module (powered by a separate USB cable). I have to use the custom connections in P20 connector...
Description: We are working with nRF54L15 connected to an external flash memory MX25R64 . Our setup uses MCUboot with a secondary partition located on the external flash....
