Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
i use nrf 52832 for scan BLE adv, sdk 12.3 ,
for reduce the missing scan signal, I use three ble_central BLE to scan, so i want set one ble_central to scan one fixed single...
I'm using the Serial_LTE_Modem application (nrf source version, zephyr v2.4.0-ncs1, mcuboot v1.6.99-ncs1, mcumgr v0.1.0-ncs1 ) with version 1.2.3 of the modem firmware. I...
Hi Nordic Leaders,
I need to complete nRF5340 based C++ Software simple solution for ONLY Data Transmit, Receive and Data Store on Flash for our Tier1 Medical client by...
I'm working with an nRF52840-MDK from MakerDiary in the nRF SDK for Thread and Zigbee. I would like to power on an LED when the chip is powered on. Here's a snippet of my...
Hi Guys，
According to the MESH document, there are two ways of node provision: PB-ADV and PB-GATT (smart phone) . A provisioner provides the unprovisioned device with provisioning...
This result is happening very seldomly but I can see it on the logs. First I get a 0x0000 result and then a 0x000A result in the fds event hanlder after calling the fds_record_update...
Hi,
Why does your web page https://infocenter.nordicsemi.com/index.jsp?topic=/struct_nrftools/struct/nrftools_nrfconnect.html&cp=8_3 titled
nRF Sniffer for Bluetooth LE...
I think this is a very simple answer but I can't find out where the file is to edit for this.
From the nRF Connect v3.6.1 - Toolchain Manager there is a drop down and "Open...
Hi everybody,
I have been reading the serialization documentation ( infocenter.nordicsemi.com/index.jsp and I am not very clear about some points.
What is it for and...
Dear all:
I want to implement FreeRTOS using NRFX, I checked the example and discovered that it uses the nrf_drv_clock... and thus it becomes a spaghetti with this legacy...
Hi,
I am working on a project that involves 2 nrf52840 DKs. One device will be running a ble application while the other device will be lookin, fetching and programming...
In SDK 1.4 we combined the udp and GPS examples and the result is unstable.
I think this could be because once enabled by RRC mode == Idle, GPS keeps going forever.
After...
Hi,
I have an issue with using the %XRFTEST command for TX testing on the LTE-M network. My setup consists of the nRF9160 DK (PCA10090) with the MFW 1.2.3 and a 1NCE SIM...
hello,
i am using two customised nrf52840 boards to get maximum range between the boards using this example https://github.com/NordicPlayground/nRF52-ble-long-range-demo...
