nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hey,
I am using SDK12, S130, nRF51822;
Trying to create a DFU update for application which Also writes over a certain area in the reserve app data, in the end of the designated...
Hi,
I'm using 52833 and S113.
My system works well, i have all my caracteristic and i'm able to read it out with nRfConnect mobile app.
But it is terribly slow .
I...
I'm using nRF52832 S132 and migrating from SDK 15.2 to SDK 17.0
My previous code used nrf_serial which appears is no longer available in SDK 17. I don't see any info in...
Hello everyone,
I would like to add ble secure bootloader on my NRF52840 dongle, I have already do that with the nrf 52832 DK But there is no example in the SDK for PCA10059...
I need to write received data from SPI to address pointed by a parameter. When doing a transfer, spi drivers also read the data sent by slave during TX. I know this is normal...
Hi all:
I am use ble_app_blinky demo sdk 16.0.0 I want to put system on idle mode,but there need to call two times sd_app_env_wait() so it can in system on idle mode.
...
Hey,
I am a new to BLE devices. I am using BL651 Laird Connectivity's 453-00005 module
and using standalone JLink OB ARM debugger to connect.
When I try to connect my...
Hi,
I want to get running the sample "lwm2m_client" on the board nRF9160DK (PCA10090).
Modem FW Version: 1.2.0.
I build the sample with Segger Embedded Studio v4.52...
Hello,
When I try to run a project containing a .cpp file, I get the following console output:
I am compiling the openthread client example with a slight modification...
Hello, I am trying to change the instance on the spi in the spi example, but unfortunately it is throwing me an error - implicit declaration of function 'NRF_DRV_SPI_INSTANCE_...
Hello,
I am using nRF52840 S140 v7.0.1. I have a query on Tx power settings.
1) In below snapshot under features, its mentioned as “4 dB steps”. So whether can I write...
Hello,
I previously used the latest SDK v17.0 on my nRF52832 PCA10040 board DK.
I ran the ble_app_uart example in order to understand how the Nordic UART Service works...
Hi all
I am doing a small personal project. I have 2 DK's :
nrf51 DK: pca10028
nrf52 DK: pca10040
Up until recently things worked fine, but suddenly i ran into a...
1. At present, using the Programmer burnmodem firmware in tool nRF Connect mfw_nrf9160_1.2.0.zip step is cumbersome.
2. Is there a simpler command line tool that can burn...
