nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I am working with nRFConnect and the nRF91-DK on MacOS Catalina.
After updating the command line tools I was able to program using the GUI
But now I want to write this...
I need to monitor how much heap was ever left available, as a minimum, after I have run my CI test suite. This is the true minimum heap ever remaining, so taking account of...
Hi -
In reading through the data sheets for the Nordic chips that support the low-rate (125 kbps) BT 5 PHY, I'm seeing Rx sensitivity numbers around -103 dBm. For the 1...
Hi,
To manufacturer production I would like to use the nrfjprog.dll in order to make an WPF C# application to program our NRF device.
I would like to use your nrfjprog...
Hello,
I am working with the nrf52832 chip and wanted to know if there are any pins that are shown on the schematic diagram, that I should not use to ensure that the Bluetooth...
Hi there,
In my application I need to send varying amounts of data (1~8KB) and store it in RAM. I trying to use memory manager library to replace the malloc() and free(...
Hi there,
I'm having some trouble piecing together an app to use V2 of the NRFX SAADC API, compounded with this being my first time using the SAADC functionality on an nRF...
I've tried to update the firmware on my Thingy:91 to version 1.2 using the file mfw:_nrf91060120.zip:
I set the Thingy:91 to ' application serial recovery mode by pushing...
I tried to play with nrf52840 and ade7953 .
At the begining, I use PC uart application to do the following test and everything works well. Here are the testing steps: 1...
I have the CLI module over UART enabled, with one command that continuously prints out the readings from a sensor. What I'm trying to do is stopping this continuous printout...
Hi,
I am using the nRF52832 and am going at it barebones because I cannot for the life of me get the SDK to work. I am using the nRF52832 manual.
-> Manual
I have two...
Hi, Im using a nRF52DK to read LIS3DH accelerometer readings in putty. Im new to this platform, I tried couple of example programs like blinkey, uart, and button in BLE. Now...
Dear All,
I am trying to implement a simple data recorder on nRF52840 DK that digitizes signals over SAADC and writes them onto the SD card. The program is working fine...
Hi,
Does anyone know where to find the BLE backwards compatibly of a given soft-device ?
I have looked at the PDF document given for my soft-device version S132, and...
