I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
hi ,
im try to add some consumer keys and system keys to the project:
nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_hids_keyboard
and my code of hids_init...
Hello! I'm trying to reach zigbee on nRF52840, and I'm trying to get a zigbee communication from light_bulb. The hex file on the sdk goes in well, and I want to add additional...
I just learn nrf52840-Dk
I can download hex and build for example light_switch mesh to nrf52840.
But light_switch project have too many C files.
Which one C file or...
Hello !!
My hardware is based on IOT application. I'm using nRF52833 SOC as end node and powered it through CR2032 coin cell. In system ON phase ( sleep mode) it is consuming...
We are having problem in decrypting the AES 128 CTR encrypted key. The key is encrypted using the example project provided in NRF5 SDK16 {aes_ctr}. The following is what is...
Folks:
I´d like to know if there is a possibility to use RUST language to compile to nRF 52 modules ?
If so, where I can find any information about it ?
Also if...
Hi,
I change the configuration in proj.conf by adding
e.g.
CONFIG_SERIAL=n
It works .
However, I want to change similar things for the mcuboot_menuconfig after...
Hi,
I want to use Zephyr OS with openthread (I use Linux as a dev platform) and I thus have tried to modify the socket echo server to my needs (I am a noob with zephyr...
Hello,
I currently designing fault handling for a firmware for nrf52840 in SES for SDK16.
At line number 68 in the hardfault_handler_gcc.c, assuming a stack overflow happened...
Hello, i have a custom board with lot of CRC ERRORS the same code, of course, works on the PDK. The spectrum transmission seems the same of the PDK.
Is it possible that...
Hi Team,
We are using the UARTE(UARTE1) module with DMA for our application with nRF52840 board, for that we are using the " libuarte " example project. For testing purpose...
Is there an example that shows the "Nordic way" of "continuous" conversions using DMA? I think a timer and PPI are needed to generate a conversion task for each timer compare...
Hello, guys!
We are using nRF52840 SoC together with the 15.3.0 version of SDK.
In our project, we basically want to combine BLE_NUS services together with the ability...
Hello!
DFU works correctly.
I try to enter chip in dfu mode from application by receiving command from SPI.
When command is received:
{ sd_softdevice_disable(); /...
Hi,
I'm using Zephyr with nrf52 and want to setup watchdog support with multiple channels (different timer settings for separate different threads).
I can add 1 channel...
