Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
i working bare-metal, using HW registers directly.... no zephyr, no SDC....
i'm able to successfully receive packets through the RADIO RX path, but now want to add a timeout...
With nrfconnect SDK V3.3.0 seeing commissioning issues with light bulb sample with nrf52840dk and google home. The logs are given below. Please help with resolution
Thanks...
Hi,
We have an application where we have a working DFU over BLE with SDK 2.9.1 but once we have migrated to 3.2.4 it has stopped working. Something has obviously changed...
Hi Nordic team,
I’m working on an nRF5340 project using MCUboot with the secondary slot placed on external flash.
I found a strange issue related to pm_static.yml . My...
Hello Team,
I am trying to test a PDM microphone (MP34DT01‑M MEMS) on the nRF9151 DK using nRF Connect SDK .
So far:
I have successfully tested I2C and I2S DAC audio...
The drag and drop programming was working fine on previous boards.
We just purchased 10 boards thinking that they were the same, but the don't seem to work.
PCA10040 3...
We are developing the nRF5340 for the Thingy91X based on Connectivity Bridge (NCS 3.2.4). I want to output logs from SWD and view them with RTT Viewer, but even when I call...
The spec. gives a 22V max for a limited amount of time. And max. 5.5V as recommended operating conditions.
But I wonder, what will be "inbetween", e.g. 7V for hours?
From...
Hi all,
I'm working on BLE time synchronization between nodes using hardware timestamps via GRTC + DPPI + PPIB cross-domain. CRCOK and PHYEND work perfectly, but adding...
Hi,
My main() program is
maiin()
{
int rc;
//rc = mcumgr_smp_client_erase(); //printk("mcumgr_smp_client_erase rc=%d\n", rc); //rc = mcumgr_smp_client_confirm_image...
The nPM1304 datasheet shows:
tshipToActive Duration SHPHLD pin must be held low to exit Ship or Hibernate mode: 96 (default)
May we know if debounce is applied to the...
Hi,
I recently started working with the nRF54L15DK and nRF Connect SDK 2.9.1. I'm trying to use I2C21 and SPI00, but I noticed that certain pins on the development kit always...
Hello.
I am experiencing an issue where Mesh communication fails after connecting to the SMP Service in the Bluetooth Mesh DFU Distributor sample.
Environment:
NCS...
Summary
On NCS v3.3.0 with CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y and a single Ethernet AIL interface (W5500), the Border Router never initialises:
ot br state → uninitialized...
Hello,
We are currently evaluating the nPM1300 as a key component on one of our new designs. This design must support both USB and solar charging using relatively low power...
