I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I have been tipped that the GPS might deliver faster fix if i change the fix interval. I've tried this with values 2,3,4 and 5, but get an error stating that the fix interval...
Hello,
We are designing a wearable that is going to use the nRF52840 and I have a question about supplying power to the unit. We are planning on using a coin cell to power...
Hi,
I am trying to compile examples/thread/freertos_coap_server with my version of openthread library. my reference is: https://infocenter.nordicsemi.com/index.jsp?topic...
I have created a folder in ble_peripheral in the examples of SDK for my project.
I am using keil uvision 5 and when I have an issue with the sdk_config.h
It states incorrect...
Hi everyone,
I'm using the nrf52832 Dev Kit PCA10040
SDK version: 15.3.0
OS: Fedora
I try to use DFU following this tutorial but I don't get the DFUTarg on the...
Hi pals!
I'm trying to establish throughput test with two nRF52840 DK and it works perfectly well except the coded PHY option. When I configure the phy option to coded,...
HI,
I am playing around with the "usbd_ble_uart_freertos" example of SDK version 15.3.
When I create another Task and try to write log entries (NRF_LOG_INFO("Test")) i...
Hi,
As well know, there have 100 channels in ESB function in nRF52832, but 2.4GHz also share with Wifi and Bluetooth.
So there have many noise if I choice wrong channel...
Hi!
I am experimenting with the ble_app_hrs_freertos example.
I would like to start two additional tasks. All works until a ble conection is made. after that my created...
Hello
I am using FDS to store some MAc addresses in my project. After successful I try fds_init() which returns error 11.
I can't figure out what is causing this error...
Hello, I have been trying to get the nrf9160DK PCA10090 version 0.8.2 to connect to your nrf cloud. I initially tried with the provided ibasis sim. I was able to get it registered...
Hi,Master:
1.The timing of the underlying nrfx_qspi_write(...) function is:a. Send 05 to check if the wip bit is 0. (Here, if wip is not 0, will it always detect until wip...
Hello,
I am going to be heading to a certification house to run tests to pass for the CE mark for our product that we used the nrf51822 on. The BLE portion of our product...
Hi everyone,
I'm trying to establish throughput test using mtu_throughput example(central-peripheral) and 2 nrf52840's but I keep getting error when set phy to coded. Here...
Hello All,
I want to know if I can run all this protocol at once? if yes can I find an example or can you suggest me a guide? I know there are examples to use BLE and ANT...
