I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello everyone!
I'm trying to build a project of gathering the information from several temperature/pressure/humidity sensors and sending it to one display.
Sensors will...
Hi, I've tried to set BLE power to max but an app error is raised when I use the sd_ble_gap_tx_power_set function. Parameters should be wrong but as far as I've read over...
How do I align UART transmission/reception with GPIO pin signaling low/high? I wanted to do this because BLE chip is receiving the Product ID & device name from microcontroller...
Hi there,
I was used IAR to compile my source, and combine with bootloader and soft device, and it was always work fine.
Now I have changed my compiling tool to SES IDE...
Hi there,
I am developing an application using an nRF52832, nRF5_SDK_12.1.0_0d23e2a and Softdevice s132 v3.0.0. The BLE part of the application involves sniffing advertising...
Hi All
On my NRF52 device I want to return my own error code after a mobile application (android) has written some data to my custom characteristic. For that I consider...
I am trying to get 2 of the nRF52840 dongles provisioned on a mesh network (client + server). (versions nRF5_SDK_15.3.0_59ac345 / nrf5SDKforMeshv310src)
I am using examples...
Hello
I'm using the NRF52832 with softdevice 132. My SDK version is 15.3. My platform is WIndows 10.
I am having trouble configuring the TWIS. I've followed the instructions...
Hi,
Here's the setup I currently have: nRF52840 SDK 15.2.0 s140 6.1.0 softdevice Secure Bootloader pca10056_usb
I'm trying to update the mbr_params_page (0xFE000) from...
I am new to the Nordic stack, and I have developed an Arduino outdoor prototype using an nRF52840 communicating with another ESP32 (BLE + WiFi) gateway. The project is used...
I use timer+ppi+pwm model.my init code like this
I use some code to close and open PWM ,like this
question:I use oscilloscopes to check PWM, I find that when I start...
Hi all, I want to work with Coded PHY on Bluetooth 5. I tried to change lines on mesh_adv.c file like below, but i getting this error : app_error_weak.c, 119, Mesh error 7...
Hi,
I modified template example and now I am trying to add usb cdc. The applicaton results in Fatal error .I found that nrf_drv_clock_init() works fine but nrf_drv_clock_lfclk_request...
Hello,
I am having difficulty getting the AT Host operating on the DK. I have DK version 0.8.5 and updated my libraries from github (in anticipating of evaluating the GPS...
I want to handle at command in main.c file. How can you do it?
For example, how can you send "AT+COPS?" and received return value?
I tested simple_at program below, but...
