I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Issue with Zephyr software platform and sleep state for the Nordic chipset. We can see when using the power management sample code for Zephyr that it consume 300 uA in sleep...
hi,...... i am merging the nRF52832 and heart rate sensor BH1790, SEGGER 15.2V i want to read the heart rate sensor , for that i want to write the paramater of address, 41h...
After beating my head against the toolchain for quite a while, I finally managed to get SES to compile the ble_app_uart for the nRF51822 using the s130 soft device. It works...
nRF52832(PCA10040) plays role of central(ble_app_multilink_central) and
HM-10(TI 254x) runs as spp peripheral.
nRF52(with SDK15) receive adertizement packet but loss...
We are using device nrf52840 with sdk 15.0.0
The problem is: High current consumption, typically around 2 mA. But over time drifts up to 9 mA in a period of 12 hrs.
...
Hi, first post here...
I've been using Nordic in the form of Laird modules and SmartBasic to get my application up & running. Now I want to migrate to using the nRF devices...
Hello,
I am trying to use nrf-mpu-examples in eclipse from this link github.com/.../nrf5-mpu-examples . I have provided all required libraries and header files but I am...
I am developing a device that will receive over the network lte a video signal in real time and display it on a screen with a resolution of 13-15 inches. Based on the chip...
I´m trying to build an application similar to the peripheral side of the app_mtu_throughput example. I need to send a large buffer via notifications to the server.
I'm using...
I am using NRF-52832 on a custom hardware. It works well on Android but on IOS (e.g. iPhone 7) it disconnects after 30 seconds.
After analysing with the sniffer, its observed...
Hi,
I had change NRF_ESB_MAX_PAYLOAD_LENGTH to 250 and modify payload_length of NRF_ESB_DEFAULT_CONFIG to 250.
Why I can only send 8 byte packet out by using "nrf_esb_write_payload...
log.zip
I use custom board for nRF52832
I connected it with JLink, and installed SD132 with nRFgo Studio (successfully)
after then, I cannot connect to chip
...
hi guy . I m triyng to understand if could be possible to send a at least 300 hz input signal beetwen two boards nrf52840 with the trasmission protocol ANT.
I tried to use...
Hi!
1. We are using 1 Client over Serial and 30+ Server nodes over mesh network
When you want to know FW info regarding Client, you can call serial command like Opcode...
Hi, I'm working on project using nRF52840-DK board with nRF5_SDK_15.2.0_9412b96. The program collects data from two UARTs, process data and sends results to Android over BLE...
