Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi @ all,
by working on a MQTT project using IoT SDK v1.0.0 (SDK v14.1) we discovered problems with TCP packets not being transmitted.
Using lwIP, transmitting TCP packets...
Hi there,
I was able to work with uart ble example described in tutorials/36/.
My question is how to disable encryption on BLE link? Specifically, we need to make disable...
Hi.
I'm testing multiperipheral function,
and have established multiple connections (1 single Peripheral with multiple Centrals).
But it seems that the Peripheral can...
I have no idea what is going on.
I am using IAR 7.8 and as I wrote, it gets reset when it hit the breakpoint.
every variable return to its initial value, and BLE get disconnected...
Hello,
I was wondering whether or not the standard analog pins on the nrf52832 have to be defined as analog inputs with the gpio methods.
I ask this because I am trying...
Hi there, I was able to work with uart ble example described in tutorials/36/.
My question is how to disable encryption on BLE link? Specifically, we need to make disable...
Hello All,
We need the following for reference purpose only
nRF6939-HW
nRFready Smart Remote 3 for nRF52 Series Hardware Files
www.nordicsemi.com/.../nRFready...
Hi,
I am building a custom PCB using the nRF51422 chip. I need to include a pushbutton switch on the PCB to generate an interrupt when it is pressed(gpiote). I am connecting...
Hi support team,
I'm using Nordic nRF52840 with PCA10056 and SDK 14.1. I have a problem with UART connection.
I have a custom board which need to hook up UART connection...
Hi! I am currently doing my project on BLE beacons. I am using nordic's nrf51822 and waveshare ble400.
I am using a blackmagic probe instead of jlink to program it using...
Hello,
my sdk is from nRF5_SDK_12.3.0_d7731ad, I added the dfu service to the ble_app_uart project on nrf51822QFAC,but it just could run to serviive_init() function and...
I am using a bootloader based on the secure serial DFU bootloader example in SDK 13 and tested it on a development kit. I noticed that hardware flow control is enabled in...
nRF52810
1,
Conditions: Two dma buffers are used, SHORT = TASK_STARTRX, 1M baud rate (10us / B)
Phenomenon: At END_RX interrupt, I called GPIO0 = low. With the logic...
Bluetooth Mesh Glossary of Terms mentions 3 different kinds of addresses: Unicast Addresses , Group Addresses and Virtual Addresses .
I think I understand what a Unicast...
I'm developing firmware for the nRF52832 in eclipse, and since I'm using the NFC pins as GPIOs I need to include the "CONFIG_NFCT_PINS_AS_GPIOS" cflag in my Makefile. However...
