Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hello,
I have working BLE peripheral_uart example based application using nRF52840 dongle with SDK v2.6.0.
I tried to upgrade SDK to v2.7.0/v2.8.0/v2.9.0.
v2.7.0 seems...
Hello,
I would like to know whether there was a way to get the name of the broadcast emitted with the sample bap_broadcast_source from a nRF5340, but directly from the...
Hi DevZone,
As mentioned in the title, the Welcome page and Application page won't show any selection for my project as following image shown.
My project is based on...
Hi,
I'd like to sample PDM at 48kHz, I'm using nRF52840 DK and nRF5 SDK.
I read a post ( devzone.nordicsemi.com/.../single-pdm-microphone-at-higher-pcm-sampling-rate)...
I'm bringing up ble_app_hrs as an eclipse project using gcc.
I'm running into an error in app_util.h, line 67:
#define STATIC_ASSERT(EXPR) typedef char static_assert_failed...
Hello,
I'm using the following setup:
nRF Connect SDK v2.9.0
B0 , upgradable secure MCUBoot, and application
Statically defined partitions in the partition manager...
I am experiencing issues configuring an SPI-based SD card interface on my nRF5340DK using NCS v2.7.0. The SD card is not initializing correctly, and I am receiving repeated...
I have two nRF52833 development boards: one is connected to the nRF21540 EK as TX (using BLE peripheral_uart), and the other is used as RX (BLE central_uart). My issue is...
Hello,
I recently updated to the "new" nrfutil tool and installed the nRF Sniffer according to the instructions. I programed the firmware and ran nrfutil ble-sniffer bootstrap...
Hi.
I am looking for help with software development for my Thingy91 project.
Project is very basic and I am ready to pay based on hour rate. It is very simple and beginner...
Hi support team,
I'm working with nRF52833 DK. installed the mobile app and desktop, but I wasn't able to connect to either.
Power switch ON, SW6 on DEFAULT. J2 connected...
Hi
The Blinky Programm only starts when I give the reset Go command via jlink commander.
At Power cycle nothing happens.
If i give the SOC an external Pin reset the...
We have written a Flutter app, which uses the Flutter-nRF-Connect-Device-Manager package to perform firmware upgrades on bluetooth devices that the app bonds with.
If iOS...
Hi,
I’m looking at starting a new design that would be based on the nrf52840, however it seems that the flash readout protection is now fairly broken on this device. Are...
Both myself and a colleague had an issue in the past 48 hours where upon launch we were prompted to install a new West workspace/SDK. In my case it "tricked" me into installing...
