Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Im mainly considerate about ANdroid and iOS devices ,I understand this is also dependent upon profile support over the android and iOS devices but this should not be an issue...
in my pca10001 board,
once i made led pin 18 and 19 pin as internal pull up.
led is not on,and i probe it also but not high.
here my config in blinky example.
...
hello
i have a problem i send from device to host the temperature, but it send the temperarture just one time
and i want that the device should send it every 10 seconds...
Hello
Im new in arduino and i want to connect an rfduino with one other rfduino
how can i send from one rfduino to other the degreee an how can i see the degree on the...
Hi!
I have a problem with testing ble_app_hrs_c. I am using nRF51822 develpment board + nRFgo Motherboard. Softdevice is S120 1.0.0 1alpha, SDK version is 5.10. Specifically...
The article that mentions the S120 and Rezence is this one: www.nordicsemi.com/.../Nordic-Semiconductor-announces-Bluetooth-Smart-solution-for-Rezence-Wireless-Charging-and...
Hello
I am new to developing with the evaluation kit and have a few very basic questions.
Any answers or pointers to relevant documents would be much appreciated.
...
I'm currently working on alert notification service. Correct me in case I misunderstand it.
having nrf51822 as peripheral with AlertNotificationServie will impose to have...
Hi,
I'd like to connect my nRF2740 to my MCU Arduino Micro and test it with the sample codes found in your GIT repo. How can I do this?
Best regards,
Alessandro
Sorry for the silly question, but as it is mandatory to use sd_X function when it is possible to avoid collision, could you tell me if this code is the right way to use the...
hello all, i need a Bluetooth low energy peripheral device in which i can attach a single button to in order to control simple phone operations, i'm not sure what device will...
Hi,
I need protection against the MITM attack, what should I modify in heart rate example? Actually, I change the characteristics to BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM...
Hi!
I am using nRF51822 evaluation kit and connecting it as a master to a pair of I2C-devices (using twi_hw_master.c). Everything works well, but when I integrated the...
Hi,
I am using the Evaluation Kit, and I have tried to send some data between the Developoment Dongle (PCA10000) to the Evaluation Kit board (PCA10001). As the Development...
Hi,
Are there any reference design for interfacing a nRF51822 with an external sensor for e.g. an accelerometer (STM LIS3DH, AD ADXL362 etc)
Also do we have a profile...
