Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
I create a linux docker container about nrf development environment. And the container host is windows11.
everything works fine except flashing function.
i passthrough...
Hello,
What would we expect the INFO.VARIANT FICR register's value to be with, for example, an nRF52811-CAAA-R7 vs. an nRF52811-CAAA-R7-B?
Right now I am seeing "AAA0...
Hi we are working on a matter project using ncs v2.6.0
Currently we are running out of RAM memory and that´s why we have moved to minimal logging by enabling
Now we...
I want to use 5" inch display for my project as nrf52840 is not able to handle that so I want to FT8xx EVE for the screen functioning? so did anyone has try this or any leads...
Dear support,
I performed a 48 hours- 20°C profiling of my 110mAh battery and managed to get my profile (really appreciate your nPM PowerUP tool. Helping a lot for development...
Hi.
I am working on a custom nRF52810 board (SDK 2.7.0).
When connecting LIS2DH12 via SPI in the .dts file, I see an error -->
.dts code -->
prj.conf -->
Please...
I try to capture the broadcast packets from the broadcast_audio_source application to investigate the BASE (which holds the configuration of BIGs, subgroups and streams)....
Hi DevZone Team,
I hope this message finds you well. I am reaching out to seek your assistance regarding the HID mouse implementation we are working on using the Nordic...
The question concerns using the nrf fuel gauge library for a setup with an nPM1300 PMIC and an NRF52840, implemented using the nRF5_SDK_17.1.0. Is it possible?
Even with the LTK key entered, wireshark cannot decode Bluetooth packets between two paired connected devices I followed this course exactly,but it failed to live up to expectations...
NRFX_TWIS_EVT_GENERAL_ERROR
I am thinking of implementing TWI slave functionality in the nRF52840.
The event handler is written as follows.
Read operations from...
I am thinking of using nRF52832 as both transmitter and receiver, and creating a firmware where the transmitter adds the acquired data to the Manufacturer Specific Data of...
Hi Nordic：
SDK version: NCS_V2.7.0
sample： peripheral_uart
config：
Compile error without any changes：
May I ask how to solve this problem？
best regards！
jermi...
Hello,
I get the error message in red when pressing Connect below:
The certificate is downloaded as instructed in the devacademy 4.2.
server_certificate.crt: ...
