nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hello,
I am trying to play with zephyr networking samples on my nRF5340 + nRF7002 EK devkit board.
I am using NCS 2.7.0 release SDK. i was able to build and run some Wi...
I'm not sure if zephyr questions can be also asked here. Problem I am struggling with is approtect mechanism to prevent flash readout. I am trying to use Zephyr config files...
Hi,
I am currently developing a custom Zigbee end device with support for FOTA updates. My FOTA seems to work (all data gets transferred correctly) but the update won't...
Hi.
I have following error:
Here is my prj.conf :
I would like to avoid using CONFIG_SHARED_INTERRUPTS.
Only GPIOTE0 is on IRQ number 11 so I couldn...
Hello,
I build the ZBOSS NCP sample from NCS v2.6.0 for the nRF52840 dongle. I use the optimization flag -O2 (for speed) in the build configuration (VS Code NCS extension...
Hi,
I am working with the Matter Light Bulb sample . I have come across a problem where I can not compile my firmware if I implement the occupancy sensor cluster using the...
Hello,
I am uploading my code with a basic URI to be advertised by the chip.
I am able to build and upload the code for the nrf52832 in my nrf52 DK, the program works...
Hello Team,
I am using nrf52840 board which supports ZIGBEE . Setup Details: Zigbee_LIGHT_BULB (nRF52840 DK) Zigbee_LIGHT_SWITCH(nRF52840 DK)
Light Bulb Example
I am...
Hi,
Currently we are using nrf52832 for our IoT finger wearable gaming mouse. Is there any newer nordic ICs with low latency features suitable for gaming applications. ...
We are looking to use the nrF5340 as a Bluetooth Classic Bridge to Auracast Transmitter.
There are some products on the market that allow you to make a standard bluetooth...
Dear
We are using the SDK15.2.0, we found after the DFU, the device reset and the consumption is normal first, but after 70+ seconds, the current consumption become abnormal...
HI all!
I've been doing some research on working with nRF Cloud and I have a few questions/clarifications:
1. In general are you able to drive/control a GPIO pin through...
I am trying to get provisioning by trusted user procedure of aws_iot working by making some changes in aws_iot nrf sample
I have tested it with permanent certificates and...
tl;dr
ZBOSS's version needs to be upgraded one by one. When migrating the SDK from 2.3.0 to 2.7.0 while preserving the persisted ZigBee network info, migrate the code to...
