Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
When using the nRF9160-DK, I flash the board with Asset Tracker V2 as provided by the instructions for the board here .
The board and SIM card are registered and the board...
Hi,
I am using custom board (nRF9160) and zephyr V2.6 and I would like to make sure that I understand the ADC settings correctly in the device tree:
channel @ 1 {
...
Hi there,
I have just tried to migrate to a new M2-based mac book pro and everything went OK (i am able to build and run my sw on the target) except that I don't have any...
hi support team，
i was testing smp_svr, i want to add button to my application that once i press the button and reset, the device will stay in mcuboot (serial port mode...
Hi,
I added build a conf to my project which has a prj.conf and select board. But the extension overwrites my configs with cache and extra cmake flags, which i dont want...
Hi there,
I'm currently trying to switch from actively advertising to a carrier wave test. This is the code snippet I'm currently debugging on SDK 17.1.0:
The code seems...
Hello, I use nRFCloud to send CoAP messages, and it's working fine under normal conditions. I am now trying to simulate a network loss, while sending some data. To do that...
I would like to create an ble5 sniffer from my thingy91. I saw that the sniffer is suitable for nrf52840 dongle and nrf52840 DK, and since thingy91 as an nrf52840 board i...
Hello,
I am currently developing a program that uses USB CDC-ACM for USB serial communication.
The USB serial communication is only used when the device is powered via...
Hello
I am developing an application on the nRF9160 SiP, that using CoAP protocol (over LTE) it connects to the nRF Cloud to transmit sensor data, get shadow register configuration...
Hello,
we are using nrf52840 with nrf5 sdk for thread and Zigbee v4.2.0.
We have been experiencing flash memory issues for a while now: https://devzone.nordicsemi.com...
Hello All, I am hoping to leverage Thingy 53's as the sensors (transmitting device) for tracking leveraging AoA. The nRF5340 DK works fine for this application as a sensor...
hi support team,
customer asks me about out 840 usb state, if we have usb low power state as below:
and below is listed in our spec or i n the USB standard ,
however...
Good night,
I am developing a Firmware for a nRF52840 created by RAKWireless RAK4631, with VSCode/Platformio/C++/FreeRTOS, and now I am changing the Architecture from a...
