Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi,
i use NRF52832
I used bootloader V5.4 and I don't see the prints I used SEGGER workspace
in sdk the settings set #define NRF_LOG_DEFAULT_LEVEL 4
what can I do...
Good day
I have been testing sample code code, but when compiling I get this error
nRF5_SDK_17.1.0_ddde560\components\libraries\uart\retarget.c:101:23: error: unknown...
I am plugging the nrf52840 Dongle to the USB port, the computer beeps as it recognizes a new USB device, but when I open the Programmer app from the NRF desktop connector...
Hi,
I am a very beginner in Python and BLE. I would like to use a nRF52840 Dongle to connect to a Bluetooth Device, send 6-Bytes data in the 1401 section and also perform...
Hi All,
i have been working on two i2c devices
1. MPR121, which has slave address (0x5A)
2. PCF8583, its address is (0xA0).
I am using Zephyr I2c api for the same...
Hi,
I would like to ask on where can I find or set the advertising duration or on how long the advertisement would last?
I am using zephyr, nrf52840DK. I want to be able...
Hello,
So, as per the requirement for my project I need to program the Thing:53 using Visual Studio code programmer following the instruction as provided in the below link...
Hi,
Is it possible to perform a HW reset of modem core inside nrf9160 device? If yes, how is this HW reset requested?
Thank you very much...
Regards,
Emerson ...
proj.conf:
nrf52840dk_nrf52840.overlay:
code:
Pretty straightforward. I've looked through the nRF52840 Product Specification and there is no mention of data bits...
From zephyr/samples/sensor/lsm6dso, I found the following code using sensor_channel_get(). API from sensor.h.
}
However, there are more driver API in zephyr/drivers...
Hello I don't see any change in RSSI with different TX power values under Zephyr. 1.9.1
It used to work with Nordic SDK 3.2.0 (see table below) The HCI API in Zephyr that...
On nRF5340, we are using Thread communication, Wifi and LTE-M module.
User can change the interface board, between Wifi or LTE-M module on the same UART bus.
& uart0...
I changed the central UART example to work with a demo I'm writing. I removed the hardware UART part and only send messages to a peripheral. What I do is I measure different...
I'm using an nRF52840 and SDKv17.1.
I have an active-high interrupt source connected to a GPIO pin. I understand that a GPIO should be able to wake up a system from system...
I think the nRF Connect toolchain is missing the right driver for the CLI app on the USB dongle, or the CLI is not setting up the USB interface with the right VIN.
When...
