Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi Team,
I want to use the Nrf52840-CAKK-R7 chip to fabricate a PCB board. And communicates with other chips by SPI interfaces.
Now, I want to select the GPIO ports by...
Hi All,
I'm using nRF9160DK PCA10090 Version 0.9.0 and I want to update the Cellular Modem Firmware using nRFConnect 3.8.0 Programmer v2.0.0. Debug Probe is switched to...
We have a timer with a number of variably sized intervals as illustrated below operating on a single capture/compare channel (CC):
Currently the method we use to set the...
Dear all,
In the datasheet and online it is mentioned that the DAP (Debug Access Port) is activated when a programmer is attached. Moreover, it can happen that the programmer...
Hello all,
I am trying the get working the example project nfc_writable_ndef_msg on a nRF52832 with the nRF5 SDK.
I have tried the others NFC examples were most are based...
Hi I am trying to update the connection interval of a peripheral device (nRF52840 ) and I have followed the steps mentioned here .
After Enabling the ble on the device I...
Hi Team,
I have several nrf52840 developing boards for developing BLE Mesh applications.
Now, I want to use SPI interfaces. I didn't find any instructions or examples...
Hi
I am struggling with timer in counter mode. What i need is the counter to calculate time between each loop in microseconds. I do not want time interrupts i just need...
I am currently writing code to read the battery voltage using the C language. I would like to include the header file "es_battery_voltage.h" and use the two functions "es_battery_voltage_get...
We are using the 52840 chip SPI interface in slave mode and communicating at about 8MHz are noticing that during periods of innactivity with all systems stopped and sleeping...
I tried to install the nRF Connect for Desktop v3.8.0 on my PC with Windows 7, but it does not connect to DK PCA10040. The nRf studio work fine with my DK. Then I install...
I am getting starting the nrf52832 board with an LSM6DSL sensor for motion recognition. it is possible in edge impulse ??
how to configure the firmware Development and how...
Hello.
I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
When making a BLE connection, you will receive an advertisement first. Then SCAN_REQ...
Hi Nordic,
I try to find an API to set the duplicate filter when scanning. But I found nothing.
I want to use the dulicapte filter disable feature to improve searching...
