Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,
I have tried to apply for the SUPL license twice now. I was denied the first time for unspecified reasons and it has been over two hours since I submitted my second...
When I program the nrf9160dk with the example, the code detects the SSD1306, but the display looks like:
The image is only using the middle half (16 rows) of the display...
Hello,
I am new to thread technology, and I would like your advice. I studied thread CLI example and thread client and server examples. However, in these examples I did...
Hi,
Is there any example or libraries available for BLE direction finding with nRF devices. Including libraries for Angle of Arrival/Angle of Departure calculations, antenna...
Hello, when I try to send data via the UART interface using a printf statement, unfortunately this does not really work. Only one byte is sent and after that the application...
hello,
I have downloaded the DTM firmware and connected it according to the serial port pins defined in the figure below,
The selection of GPIO pins are pin 18 for RX...
I am trying to use the nRF as an intermediary bootloader for another microcontroller. All that I need the nRF to do is accept a 64kB binary file from my computer (at the moment...
Hello,
I have been testing the " ble_app_multilink_central " example given with Nordic SDK * nRF5_SDK_16.0.0_98a08e2 *.
nRF52840_DK board is working as the multilink...
I am getting an error when trying to run nrfutil, any tips on how to fix this?
~ ᐅ pip3 install --user nrfutil Requirement already satisfied: nrfutil in ./.local/lib/python3...
Hi,
I am developing project using nrf52840 and currently developing using SDK 3.0. (Once I complete my feature I will update to SDK4.1).
I am using the light bulb firmware...
Hello I am trying to run a simple zephyr bluetooth sample using nrf Connect SDK v. 1.5.1 I am using your nRF5340 DK The sample I am running is: beacon I followed your instructions...
I have one TX and another RX codes for data communication by ESB protocol. To verify whether data whitening can be enabled, I added below register setting on TX side only...
Hi. I'm developing nRF52832.
I'm in the process of setting up BLE, but there's a problem.
There was a problem while I was organizing the files due to successful BLE communication...
Hi,
I can able to get the DEVADDR0 and DEVADDR1. I am not able to make out How this EUI64 id is calculated using the DEVADDDR value.
I always get F4CE36 starting numbers...
