Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
I have several applications that continuously scan on Bluetooth that have started exhibiting a new failure mode after upgrading nrfxlib from v2.9.0 to v3.0.2 ( https://github...
For our custom nrf9151 board,
The following is the prj.conf:
There are no pullups on any GPIO and for now, assume there are no peripherals connected, but there is a...
Hi,
We are having issues with this part bridging on our via-in-pads. We are using 2oz finished outer layer copper.
Do you have any footprint recommendations for 2oz copper...
Hi,
I would like to know the value of the Noise Figure for the nRF52840. How much dB is it? I am looking at the documentation of the nRF 52840 but could not find the value...
Hi Nordic team,
I'm currently working on a device onboarding flow using the nRF Connect SDK Toolchain v2.6.0 on an nRF52840 board . The onboarding process involves:
...
I am building the sample project C:\ncs\v2.5.0\nrf\samples\bluetooth\peripheral_uart, which supports MCUboot’s serial recovery of the networking core image on nRF5340DK. ...
My Power Profile Kit (PPK2) having issue after a firmware update. Now it's not even turn on the light when connected and with power switch on. I think I accidentally update...
My company does firmware consulting work. We have been asked to create a Green Power Device (Wall Light Switch) on the Nordic nRF52833 chip.
From our research It does...
I have make a PCB with a BLE5340PA module from Ezurio using the nordic 5340 soc, i want to programm the soc but it seem that there is no boot on the module.
Fortunately...
I have a preset stored in CMakePresets.json:
When I go to create a new build configuration with the preset, the extension creates an Extra CMake Arguments row with:
...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Hi all,
I'm working on an application using the nRF54L15 with NCS v2.9.0 and Zephyr RTOS. The device performs BLE scanning using the following parameters:
When deployed...
Hello Team,
We are working on nrf54l15 platform and using nrf connect SDK 3.0.2 We have added the support of DFU over BLE using following steps:
1. Added " CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
Can anyone clarify what information is stored in the nrf9160 chip barcode? For our manufacturing tests, we'd like to use a barcode-readable identifier on each board, and the...
