Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi,
We have 2 projects in pre-production stage that use nRF52840. We are also using FreeRTOS for both projects.
Now we need to create an OTA bootloader for both. There...
SDK: 17.0.0
Hardware: E-Byte E73-2G4M04S1B module
Chipset: NRF52832 QFAA QFN48
Running the hids examples, I noticed that the hids_mouse example will go from Fast Adv...
Do I need to carry out ANSI C63.27 regulatory test for coexistence of wireless communication that share the 2.45GHz band if we designed a custom PCB BLE antenna for NRF52840...
Hi,
I have the nRFgo Starter Kit with the radio module (nRF2427LE1) attached. First, does the radio module not have a bootloader already downloaded to it? Next, when I...
Dear Support Team.
We want to support secure DFU on mobile and desktop platforms. Do you have any documentation to implement this on Mac OSX and Windows?
Its an open...
Hi, is there any LE audio sample for NRF5340?
I know the upper layer protocol is under developing on Bluetooth SIG, but is there any possible way to direct use the HCI command...
Hi
I'm developing with nRF52832.
I am using Segger Enbed Studio as a development tool.
When you download a program from Segger, Segger does reset once, and I wonder...
Hi,
I want to run QSPI application example on my nRF52840DK (PCA10056) board with logs seen via UART. I successfully uploaded QSPI bootloader example and Blinky SysTick...
Hello,
I'm developing an BLE application with NCS where I want to be able to change the BLE device name during runtime. Therefore I enabled CONFIG_BT_DEVICE_NAME_DYNAMIC...
Now we development a switch and use it control the light. When i push switch close the light, there was still a faint light. Then i found when NVIC_SetPendingIRQ(EVENT_IRQn...
What I intended was to write x'700' to x'10001080' i.e. NRF_UICR->CUSTOMER[0] !
When ran my application, which outputs NRF_UICR->CUSTOMER[0] to the log, I was very confused...
In firmware I can read the programmed UICR serial number as follows: -
uint32_t serial;
memcpy(&serial, (uint32_t*)0x10001080, 4);
Is it possible to program the UICR...
The peripheral_lbs sample on the nRF5340 with the nRFConnect v1.5.0 builds fine and the merged.hex file downloads fine, but it does not appear to be running, no blinking light...
I have a program that recieves data from another chip over Serial. It sends 2048 blocks of data which than get transmitted to our C2 over mqtt. Problem is that afther 12/14...
