Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello,
we have a problem to do bonding to a Huawei P20 lite, which has Android 9 and seems to use BLE 4.2.
We use the nRF52832, with SD 17.2.0, using Bluetooth LE.
We...
Hi I have a new NRF5340-PDK board. I am using Zephyr OS to build my application like that: However, flashing with: doesn't work. I am using the latest version of nrfjprog...
Hello all,
We sell BLE devices with pre-programmed firmware, which has the ability to be remotely updated using the nordic buttonless DFU service based on a modified version...
Hi,
Thanks in advance.
Anybody experiencing the same problem? I'm trying to test the DFU functionality by compiling the example in SDK/examples/dfu/secure_bootloader/pca10040_ble...
Hi,
I've just learned that even with enabled pairing, it's still possible to "simply" connect to the device. But is there a way to force pairing on connection?
I'm...
hi,
i am using nrf52832 devkit and max30208 temp. sensor. i am not getting updated data. iprefer this link for i2c address.( https://os.mbed.com/users/cyberjoey/code/OT07_I2C_GUI_Firmware...
We are implementing a protocol using the softdevice s140 multiprotocol API. The protocol is always listening, but occasionally transmitting.
To manage this setup, we request...
Hi,
I am exploring the idea of removing the JTAG port from the PCB to make it difficult to maliciously change the firmware on the field. I have the secure UART Boot-loader...
Hello
I am developing a firmware for nrf52832 using buttons like if I continuosly press my button for 6 seconds it will go to active mode from sleep mode and have been using...
Dear sir,
I have a light sensor connected to P0.04/AIN2 on 52820. How can i get the change of voltage?
I use the COMP, and has enabled COMP_ENABLED in sdk_config.h, compiled...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
We have a standalone application with no SDK integration. We would like to have the possibility to do OTA Updates via BLE and maybe introduce BLE support later on.
So for...
Hi,
I am trying to run IPSP example from nRF Connect SDK 1.4.2 IPSP sample (v1.4.2\zephyr\samples\bluetooth\ipsp). The "ping6 -I bt0 ff02::1" command is working fine but...
Hi, I am using the nRF52840 DevBoard with SDK 16.0 and Mesh SDK 4.1 and am building on the light_switch_client example.
I am trying to change the publication address by...
