Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hi, I have one service UUID ffe0 that has two characteristics: one of has UUID ffe4 use for "notify" and other one has UUID ffe5 use for "write and read". Now i want to get...
Hello,
I'm having a system consisting of an nRF52 and another processor, with UART between them. If the other processor restarts, nRF's RX line will be pulled low for some...
Hi,
I'm trying to add LESC pairing mechanism to NUS.
Now when I'm doing pairing between nRF52DK and Phone(Android) via normal way, the behavior is what I want. Please...
Hi there,
I am using nRF5_SDK 16 with PCA10056 and Fanstel EV-BT840-V4. I am testing my example with BT-840 module as we will use it for our final product.
First i tried...
SDK: 15.3.0 Sample: ble_app_hids_keyboard Device: EYSHJNZWZ (nRF52832)
I have a question about HID. In the sample program "ble_app_hids_keyboard", the following values are...
SDK: 15.3.0 Sample: ble_app_hids_keyboard Device: EYSHJNZWZ (nRF52832)
I have a question about HID. In the sample program "ble_app_hids_keyboard", "report_map_data" stores...
Hi,
I am measuring a frequency using the ADC (200ksps) and saving the samples into an array. I save 128 samples then move that data to the fft module to check what the signal...
Currently, debug probes - STLink, JLink, OpenOCD, Black Magic Probe, DAPLinkda, etc. connect to a host PC over a USB, serial or network port and then connect to a target ...
I get ACI_BOND_STATUS_FAILED_ENCRYPTION_KEY_SIZE error when I try to bond my nrf8001 peripheral to my iPhoneX. The min and max key sizes are set to 7 and 16.
Any Idea?
Hi,
I'm using the ble_app_uart example as a starting point for my project. Basically I want to program the nRF52 DK to receive data from another device via UART, store them...
Hi Nordic,
I'm working on a project with very limited board space. I'd like to have the option for both SWD and GPIOs to share the same test points on the board. Ideally...
There is an issue in SDK for Thread & Zigbee 4.1.0 release. It does not appear in previous releases. The problem manifests itself as higher current consumption, as shown in...
I flashed nrf52840 usb dongle via SWD and now it can't go to DFU mode even if I press reset.
Green and blue leds are constantly blinking. How can I go to DFU mode in that...
Hi all,
I am developing ADC functions with Mynewt on nrf52 DK PCA10040 board.
The working example code based on SAADC driver nrfx 1.7.0 won't work on nrfx 2.1.0.
Example...