Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hello,
I need to use USB 2.0 connection as a USB MSC device as well have it communicate over a USB 2.0 connection to a Wi-Fi module.
I know there is a USB 2.0 built into...
I'm working on a project using nRF9160 DK.
How can you use MQTT+TLS in nRF9160?
Where should ca certificate file be stored?
I modified the code below in mqtt_simple...
hello i am using nrf52832 DK and working UART_APP_BLE , i want know where the data will be stored when we send any message through mobile to the device. can we see the received...
Hi, I am new at programming.
I am trying to program nRF51822 DK. But My Desktop can't appear J-Link Debugger as a USB drive.
I read some posts about that but I didn't...
Hi .......Clan
I am planning to make chatbox mean chatting (transferring the messages) between the central and peripherals even peripheral to peripheral , and device peripheral...
Im using MCP6S21 amplifier which takes input from some I to V converter and output of amplifier is connected to nrf52832 via I2C pins so how to change or vary gain of amplifier...
I am having a problem running MQTT_Simple on my nRF9160 DK.
The COM Port shows the following:
***** BUS FAULT ***** Precise data bus error BFAR Address: 0x4002a514 **...
Hi.
I am using the nrf9160 with the latest firmware and with all the instructions followed, I get this error . Faulting instruction address = 0x3648 Fatal fault in ISR!...
Hi,
I am working on mesh bluetooth using nrf52832 with PCA10040 , I used example from nrf5_SDK_for_Mesh_v2.0.1_src , my questions are
1.How many bytes(Max and min) can...
Our device allows only one device to pair and delete the original pairing information when there is a new device paired. Restore the original pairing information if there...
Hi,
I am using the nrf52832 dk for my project.
I am using the RX characteristic of the NUS example to send data from the phone to the dk.
In the same code i am also...
I tried to build the "nRF5_SDK_15.1.0_a8c0c4d\examples\crypto\nrf_crypto\aes\aes_all_cli\pca10056\blank" source code but I got the following error,
.\_build\nrf52840_xxaa...
Hello,
While i am trying to find the definition of SER_REQ_ENC_BEGIN(SD_BLE_GAP_ADV_START); it is there in the file ble_gap_app.c
When i right click on that function...
What is the difference between nrf5232, 1.8V and 3.3V power supplies? What should watch out for when replacing a 3.3V power supply with a 1.8V power supply?
