the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
I followed instructions given here https://devzone.nordicsemi.com/b/blog/posts/segger-embedded-studio-a-cross-platform-ide
I got it working in Build and Debug mode. However...
Dear Sir,
I am calling the function sd_ble_gap_disconnect() to disconnect the peripheral from the App.
This is called inside ble_evt_handler() function and under
...
I'm looking for Memory LCD shield like using nRF52840 long range demo.
The shield name is probably PCA63520. However I can not find it.
Where can I get it?
In the folder for the sd_api_v6 there are the headers for the softdevice S140: pc-ble-driver_v4.0.0\src\sd_api_v6\sdk\components\softdevice\s140\headers
I have a custom...
I want to use the CUSTOMER[] fields for their apparent intended purpose of storing calibration data in nonvolatile memory. I find it quite absurd that the softdevice would...
Hi,
I am using PWM to control LED power.
The code i use for initializing the PWM is-
app_pwm_config_t pwm1_cfg = APP_PWM_DEFAULT_CONFIG_2CH(1000L, PIN1, PIN2); err_code...
Hello,
I am trying to run the example DFU over TFTP. I have setup a tftp server with following configurations:
# /etc/default/tftpd-hpa TFTP_USERNAME="tftp" TFTP_DIRECTORY...
Hi,
I've followed the link https://devzone.nordicsemi.com/f/nordic-q-a/35675/how-to-use-static-passkey-for-a-no-display-no-output-peripheral
and added it to uart example...
Hi,
My app requests a timeslot in various conditions - sometimes the timeslot needed is long, sometimes short (unknown a priory) so it asks for the longest possible...
Hi,
Is there any easier way when using Eclipse IDE with GCC for nRF5 SDK 15.2 development to get the Include files in the examples to be recognized easier than tediously...
My set up contains beagle bone black as Application board. PCA10001 board with S120 Softdevice using nordic_sdk_10 running ble_connectivity example program.
I initiated...
I have a Teledyne protocol analyzer for capturing over the air data between an nRF52840-DK and an iPhone 8 device. How do I obtain the encryption key from the nRF52840 SoC...
Hi,
I want to verify Bluetooth on my board is good or bad.
Note that, I do not have any spectrum analyzer or vector network analyzer, just development kit.
I found example...
On the product page the nRF52810 is mentioned as supporting ANT. https://www.nordicsemi.com/eng/Products/nRF52810
However in the info-center looking at the compatibility...
Apologies if this is a Segger question vs a Nordic question.
I have already been evaluating SES for a non-Nordic project, and so it's already installed [on Mac].
I am...
