Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hello Nordic support team I want to send command from hm10 ble chip to Nrf52832 dk board.So before I start to implement this I want to know that HM10 ble chip can communicate...
Hi, all.
I want data read from gyro sensor through i2c, and then send it through bluetooth equipment.(PC or iPhone and so on)
But i don'k know how to send gyro sensor...
I am asking about using the sd_rand_application_vector_get function; it seems that it causes my board to crash, and it never returns a success code.
I have already seen...
Hello:
I am upgrading my application to use Mesh SDK 3.0.0 (I was at 2.1.1). In my application, I process the mesh from the main loop (per the instruction in the Interrupt...
Hello All, I would like to implement tracking over MESH network using nRF52840. 1. In my MESH network, there are some devices who continuously advertising (say beacon). 2...
HI.
I am following the document http://infocenter.nordicsemi.com/pdf/nRFConnect_BLE_User_Guide_v2.2.pdf to work with nRFConnect desktop App and my DK BMD300(Rigado). ...
Hello,
I'm trying to play voice using PWM in nRF51822.
I've already experienced this using other MCU before.
So. I'm trying.
Voice source data is 8bit / 8K / mono...
Hi,
I am working on nrf52832 , SDK15 and softdevice S132. I am modifying the ble_app_hrs example code in SDK
I was trying to implement a whitelist with the address of...
I am using ble_app_uart SDK_11 s130 on nRF51-dk. I would like to make the device running on ble_app_uart connectable but not discoverable. The Android app will have pre-knowledge...
I am using nRF52840 with sdk 15.0 version. I am able to read OR write data into flash using fds library. But now i want to write one or two bytes into flash and read this...
Development Kit - nrf52
SDK Version - 15.0.0
IDE - Segger Embedded Studio
Computer Platform - Windows 7 - 64 Bit
Setup : I am trying to interface an E Paper Display...
I am trying to detect when mtu has been successfully negotiated through the ble_evt_handler function, which is passed into NRF_SDH_BLE_OBSERVER as shown below:
// Register...
Hi - I'm trying to program the Thingy52 using my nRF52840 DK and Macbook Pro. I've got the Thingy connected to the DK via the 10-pin cable. The first time I ran nrfjprog on...
