Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I refer to and the answer answer given by AI referring me to you.
I need the lithium battery only to about 8-bit accuracy to reduce the leakage current. Please provide...
Hi,
I'm new to fuel gauging and battery profiling and am trying to understand the process and the parameters used.
Is there a description of how a battery model is created...
Hi all, I want to program a nRF5340 microcontroller to become a peripheral BLE device. I use the Zephyr with nRF Connect SDK 2.7.0 and VSCode as IDE. I have a custom electronic...
After updating my nRF Connect Command Line Tools to version 10.24.2 on my 2019 Intel MacBook Pro 16 running Sonoma 14.4.1, I've encountered an issue where the Flash action...
Hello!
I have an issue with the nRF5340 when using it with an M1 MacBook Air. When I connect it to the laptop I get a notification about JLink ejecting every few seconds...
Hello! I need to post, but can't since december, why?
I have updated Windows 11, SDK 2.6.1 and 2.8.0 default is 2.6.1
Board SDK nrf9151
I need to use http_client or...
Hi
We have a third party that develops some of our products, and this third party does not release their source code. However, we would like to sign our binaries with a...
Hi,
Platform: nRF54L15, SDK 2.9
The application is Matter + BLE. CONFIG_CHIP_DFU_OVER_BT_SMP & MCUBoot are part of the configuration. As soon as we enable the BLE...
I have problems with nRF Connect(Android, latest Version, no version number found) to find BLE devices with 2M phy, coded phy and extended advertising. So i am running nRF...
I have made my own NRF52832 Dev board as in the next image:
I received the board, and ICs and hand-soldered them in my home.
however, I am still a newbie in nRF SDK...
Hi, I was trying to flash the sweyntooth firmware to nRF52840 dongle using nRF connect for desktop. I was following the instruction on in this tutorial: . The hex file I used...
I'm currently developing a BLE Long Range application based on Zephyr and the v2.8.0 version of the nRF Connect SDK. The app is based on the following nRF samples: central_hr_coded...
Hello,
I am currently stuck trying to migrate a project to the 2.8.0 version of the NC SDK.
I followed the exercice of the Nordic Academy : FOTA over BLE .
It works...
I want to automatically reconnect to my peripheral (nrf5340 DK) from my central (phone) when there is an accidental disconnect (out of range) which I am simulating by resetting...
